Tritium

Tritium, ³H

General
Symbol	3H
Names	tritium, 3H, H-3, hydrogen-3, T, 3T
Protons (Z)	1
Neutrons (N)	2
Nuclide data
Natural abundance	10−18 in hydrogen[1]
Half-life (t1/2)	12.32 years
Isotope mass	3.01604928 Da
Spin	⁠1/2⁠
Excess energy	14949.794±0.001 keV
Binding energy	8481.7963±0.0009 keV
Decay products	3He
Decay modes
Decay mode	Decay energy (MeV)
Beta emission	0.018590
Isotopes of hydrogen Complete table of nuclides

Tritium (from Ancient Greek τρίτος (trítos) 'third') or hydrogen-3 (symbol T or ³H) is a rare and radioactive isotope of hydrogen with half-life ~12.3 years. The tritium nucleus (t, sometimes called a triton) contains one proton and two neutrons, whereas the nucleus of the common isotope hydrogen-1 (protium) contains one proton and no neutrons, and that of non-radioactive hydrogen-2 (deuterium) contains one proton and one neutron. Tritium is the heaviest particle-bound isotope of hydrogen. It is one of the few nuclides with a distinct name. The use of the name hydrogen-3, though more systematic, is much less common.

Naturally occurring tritium is extremely rare on Earth. The atmosphere has only trace amounts, formed by the interaction of its gases with cosmic rays. It can be produced artificially by irradiation of lithium or lithium-bearing ceramic pebbles in a nuclear reactor and is a low-abundance byproduct in normal operations of nuclear reactors.

Tritium is used as the energy source in radioluminescent lights for watches, night sights for firearms, numerous instruments and tools, and novelty items such as self-illuminating key chains. It is used in a medical and scientific setting as a radioactive tracer. Tritium is also used as a nuclear fusion fuel, along with more abundant deuterium, in tokamak reactors and in hydrogen bombs. Tritium has also been used commercially in Betavoltaic devices such as NanoTritium batteries.

Tritium was first detected in 1934 by Ernest Rutherford, Mark Oliphant and Paul Harteck after bombarding deuterium with deuterons (deuterium nuclei). Deuterium is another isotope of hydrogen, which occurs naturally with an abundance of 0.015%.^[2][3] Their experiment could not isolate tritium, which was first accomplished in 1939 by Luis Alvarez and Robert Cornog, who also realized tritium's radioactivity.^[4][5] Willard Libby recognized in 1954 that tritium could be used for radiometric dating of water and wine.^[6]

The half life of tritium is listed by the National Institute of Standards and Technology as 4,500 ± 8 days (12.32 ± 0.02 years)^[7] – an annualized rate of approximately 5.5% per year. Tritium decays into helium-3 by beta-minus decay as shown in this nuclear equation:

3 1H

→

3 2He

+

e−

+

ν e

releasing 18.6 keV of energy in the process. The electron's kinetic energy varies, with an average of 5.7 keV, while the remaining energy is carried off by the nearly undetectable electron antineutrino. Beta particles from tritium can penetrate only about 6.0 millimetres (0.24 in) of air, and they are incapable of passing through the dead outermost layer of human skin.^[8] Because of their low energy compared to other beta particles, the amount of bremsstrahlung generated is also lower. The unusually low energy released in the tritium beta decay makes the decay (along with that of rhenium-187) useful for absolute neutrino mass measurements in the laboratory.

The low energy of tritium's radiation makes it difficult to detect tritium-labeled compounds except by using liquid scintillation counting.

Tritium is most often produced in nuclear reactors by neutron activation of lithium-6. The release and diffusion of tritium and helium produced by the fission of lithium can take place within ceramics known as breeder ceramics. Production of tritium from lithium-6 in such breeder ceramics is possible with neutrons of any energy, though the cross section is higher when the incident neutrons have lower energy, reaching more than 900 barns for thermal neutrons. This is an exothermic reaction, yielding 4.8 MeV.^[9] In comparison, fusion of deuterium with tritium releases about 17.6 MeV. For applications in proposed fusion energy reactors, such as ITER, pebbles consisting of lithium bearing ceramics including Li₂TiO₃ and Li₄SiO₄, are being developed for tritium breeding within a helium-cooled pebble bed, also known as a breeder blanket.^[10]

⁶
₃Li
+ n → ⁴
₂He
(2.05 MeV) + ³
₁H
(2.75 MeV)

High-energy neutrons can also produce tritium from lithium-7 in an endothermic reaction, consuming 2.466 MeV. This was discovered when the 1954 Castle Bravo nuclear test produced an unexpectedly high yield.^[11] Prior to this test, it was incorrectly assumed that ⁷
₃Li
would absorb a neutron to become ⁸
₃Li
, which would beta-decay to ⁸
₄Be
, which in turn would decay to two ⁴
₂He
nuclei on a total timeframe much longer than the duration of the explosion.

⁷
₃Li
+ n → ⁴
₂He
(2.05 MeV) + ³
₁H
(2.75 MeV) + n

High-energy neutrons irradiating boron-10, also occasionally produce tritium:^[12]

¹⁰
₅B
+ n → 2 ⁴
₂He
+ ³
₁H

A more common result of boron-10 neutron capture is ⁷Li and a single alpha particle.^[13]

Especially in pressurized water reactors which only partially thermalize neutrons, the interaction between relatively fast neutrons and the boric acid added as a chemical shim produces small but non-negligible quantities of tritium.

Tritium is also produced in heavy water-moderated reactors whenever a deuterium nucleus captures a neutron. This reaction has a small absorption cross section, making heavy water a good neutron moderator, and relatively little tritium is produced. Even so, cleaning tritium from the moderator may be desirable after several years to reduce the risk of its escaping to the environment. Ontario Power Generation's "Tritium Removal Facility" is capable of processing up to 2,500 tonnes (2,500 long tons; 2,800 short tons) of heavy water a year, and it separates out about 2.5 kg (5.5 lb) of tritium, making it available for other uses.^[14] CANDU reactors typically produce 130 grams (4.6 oz) of tritium per year, which is recovered at the Darlington Tritium Recovery Facility (DTRF) attached to the 3,512 MW_electric Darlington Nuclear Generating Station in Ontario. The total production at DTRF between 1989 and 2011 was 42.5 kilograms (94 lb) – with an activity of 409 megacuries (15,100 PBq): an average of about 2 kilograms (4.4 lb) per year.^[15]

Deuterium's absorption cross section for thermal neutrons is about 0.52 millibarn, whereas that of oxygen-16 (¹⁶O) is about 0.19 millibarn and that of oxygen-17 (¹⁷O) is about 240 millibarns. While ¹⁶O is by far the most common isotope of oxygen in both natural oxygen and heavy water; depending on the method of isotope separation, heavy water may be slightly richer in ¹⁷O and ¹⁸O. Due to both neutron capture and (n,α) reactions (the latter of which produce ¹⁴C, an undesirable long-lived beta emitter, from ¹⁷O) they are net "neutron consumers" and are thus undesirable in a moderator of a natural uranium reactor which needs to keep neutron absorption outside the fuel as low as feasible. Some facilities that remove tritium also remove (or at least reduce the content of) ¹⁷O and ¹⁸O, which can – at least in principle – be used for isotope labeling.

India, which also has a large fleet of pressurized heavy water reactors (initially CANDU technology but since indigenized and further developed IPHWR technology), also removes at least some of the tritium produced in the moderator/coolant of its reactors but due to the dual use nature of tritium and the Indian nuclear bomb program, less information about this is publicly available than for Canada.

Tritium is an uncommon product of the nuclear fission of uranium-235, plutonium-239, and uranium-233, with a production of about one atom per 10⁴ fissions.^[16][17] The main pathways of tritium production include ternary fission. The release or recovery of tritium needs to be considered in the operation of nuclear reactors, especially in the reprocessing of nuclear fuel and storage of spent nuclear fuel. The production of tritium is not a goal, but a side-effect. It is discharged to the atmosphere in small quantities by some nuclear power plants.^[18] Voloxidation is an optional additional step in nuclear reprocessing that removes volatile fission products (such as all isotopes of hydrogen) before an aqueous process begins. This would in principle enable economic recovery of the produced tritium but even if the tritium is only disposed and not used, it has the potential to reduce tritium contamination in the water used, reducing radioactivity released when the water is discharged since tritiated water cannot be removed from "ordinary" water except by isotope separation.

Annual discharge of tritium from nuclear facilities^[19]

• v
• t
• e

Location	Nuclear facility	Closest waters	Liquid (TBq)	Steam (TBq)	Total (TBq)	Total (mg)	year
United Kingdom	Heysham nuclear power station B	Irish Sea	396	2.1	398	1,115	2019
United Kingdom	Sellafield reprocessing facility	Irish Sea	423	56	479	1,342	2019
Romania	Cernavodă Nuclear Power Plant Unit 1	Black Sea	140	152	292	872	2018
France	La Hague reprocessing plant	English Channel	11,400	60	11,460	32,100	2018
South Korea	Wolseong Nuclear Power Plant	Sea of Japan	107	80.9	188	671	2020[20]
Taiwan	Maanshan Nuclear Power Plant	Luzon Strait	35	9.4	44	123	2015
China	Fuqing Nuclear Power Plant	Taiwan Strait	52	0.8	52	146	2020
China	Sanmen Nuclear Power Station	East China Sea	20	0.4	20	56	2020
Canada	Bruce Nuclear Generating Station A, B	Great Lakes	756	994	1,750	4,901	2018
Canada	Darlington Nuclear Generating Station	Great Lakes	220	210	430	1,204	2018
Canada	Pickering Nuclear Generating Station Units 1-4	Great Lakes	140	300	440	1,232	2015
United States	Diablo Canyon Power Plant Units1, 2	Pacific Ocean	82	2.7	84	235	2019

Given the specific activity of tritium at 9,650 curies per gram (357 TBq/g), one TBq is equivalent to roughly 2.8 milligrams (0.043 gr).

In June 2016 the Tritiated Water Task Force released a report^[21] on the status of tritium in tritiated water at Fukushima Daiichi nuclear plant, as part of considering options for final disposal of the stored contaminated cooling water. This identified that the March 2016 holding of tritium on-site was 760 TBq (equivalent to 2.1 g of tritium or 14 mL of pure tritiated water) in a total of 860,000 m³ of stored water. This report also identified the reducing concentration of tritium in the water extracted from the buildings etc. for storage, seeing a factor of ten decrease over the five years considered (2011–2016), 3.3 MBq/L to 0.3 MBq/L (after correction for the 5% annual decay of tritium).

According to a report by an expert panel considering the best approach to dealing with this issue, "Tritium could be separated theoretically, but there is no practical separation technology on an industrial scale. Accordingly, a controlled environmental release is said to be the best way to treat low-tritium-concentration water."^[22] After a public information campaign sponsored by the Japanese government, the gradual release into the sea of the tritiated water began on 24 August 2023 and is the first of four releases through March 2024.^[23] The entire process will take "decades" to complete.^[24] China reacted with protest.^[25][26] The IAEA has endorsed the plan. The water released is diluted to reduce the tritium concentration to less than 1500 Bq/L, far below the limit recommended in drinking water by the WHO.^[27]

Tritium's decay product helium-3 has a very large cross section (5330 barns) for reacting with thermal neutrons, expelling a proton; hence, it is rapidly converted back to tritium in nuclear reactors.^[28]

³
₂He
+ n → ¹
₁H
+ ³
₁H

Tritium occurs naturally due to cosmic rays interacting with atmospheric gases. In the most important reaction for natural production, a fast neutron (which must have energy greater than 4.0 MeV^[29]) interacts with atmospheric nitrogen:

¹⁴
₇N
+ n → ¹²
₆C
+ ³
₁H

Worldwide, the production of tritium from natural sources is 148 petabecquerels per year. The global equilibrium inventory of tritium created by natural sources remains approximately constant at 2,590 petabecquerels. This is due to a fixed production rate, and losses proportional to the inventory.^[30]

Tritium for American nuclear weapons was produced in special heavy water reactors at the Savannah River Site until their closures in 1988. With the Strategic Arms Reduction Treaty (START) after the end of the Cold War, the existing supplies were sufficient for the new, smaller number of nuclear weapons for some time.

225 kg (496 lb) of tritium was produced in the United States from 1955 to 1996.^[a] Since it continually decays into helium-3, the total amount remaining was about 75 kg (165 lb) at the time of the report,^[31][11] and about 16 kg (35 lb) as of 2023.^[32]

Tritium production was resumed with irradiation of rods containing lithium (replacing the usual control rods containing boron, cadmium, or hafnium), at the reactors of the commercial Watts Bar Nuclear Plant from 2003 to 2005 followed by extraction of tritium from the rods at the Tritium Extraction Facility at the Savannah River Site beginning in November 2006.^[33][34] Tritium leakage from the rods during reactor operations limits the number that can be used in any reactor without exceeding the maximum allowed tritium levels in the coolant.^[35]

Tritium has an atomic mass of 3.01604928 Da. Diatomic tritium (T₂ or ³H₂) is a gas at standard temperature and pressure. Combined with oxygen, it forms tritiated water (³H₂O).

Compared to hydrogen in its natural composition on Earth, tritium has a higher melting point (20.62 K vs. 13.99 K), a higher boiling point (25.04 K vs. 20.27 K), a higher critical temperature (40.59 K vs. 32.94 K) and a higher critical pressure (1.8317 MPa vs. 1.2858 MPa).^[36]

Tritium's specific activity is 9,650 curies per gram (3.57×10¹⁴ Bq/g).^[37]

Tritium figures prominently in studies of nuclear fusion due to its favorable reaction cross section and the large amount of energy (17.6 MeV) produced through its reaction with deuterium:

³
₁H
+ ²
₁H
→ ⁴
₂He
+ n

All atomic nuclei contain protons as their only charged particles. They therefore repel one another because like charges repel (Coulomb's law). However, if the atoms have a high enough temperature and pressure (for example, in the core of the Sun), then their random motions can overcome such repulsion, and they can come close enough for the strong nuclear force to take effect, fusing them into heavier atoms.

A tritium nucleus (triton), containing one proton and two neutrons, has the same charge as any hydrogen nucleus, and it experiences the same electrostatic repulsion when close to another nucleus. However, the neutrons in the triton increase the attractive strong nuclear force when close enough to another nucleus. As a result, tritium can fuse more easily with other light atoms, than ordinary hydrogen can.

The same is true, albeit to a lesser extent, of deuterium. This is why brown dwarfs ("failed" stars) cannot fuse normal hydrogen, but they do fuse a small minority of deuterium nuclei.

Like the other isotopes of hydrogen, tritium is difficult to confine. Rubber, plastic, and some kinds of steel are all somewhat permeable. This has raised concerns that if tritium were used in large quantities, in particular for fusion reactors, it might contribute to radioactive contamination, though its short half-life should prevent significant long-term accumulation in the atmosphere.

The high levels of atmospheric nuclear weapons testing that took place prior to the enactment of the Partial Nuclear Test Ban Treaty proved to be unexpectedly useful to oceanographers. The high levels of tritium oxide introduced into upper layers of the oceans have been used in the years since then to measure the rate of mixing of the upper layers of the oceans with their lower levels.

Since tritium is a low energy beta (β) emitter, it is not dangerous externally (its β particles cannot penetrate the skin),^[30] but it can be a radiation hazard if inhaled, ingested via food or water, or absorbed through the skin.^{[38][39][40][41][42]}

Organisms can take up H³HO, as they would H₂O.^[43] Plants convert H³HO into organically bound tritium (OBT), and are consumed by animals. H³HO is retained in humans for around 12 days, with a small portion of it remaining in the body.^[44] Tritium can be passed along the food chain as one organism feeds on another, though the metabolism of OBT is less understood than that of H³HO.^[44] Tritium can incorporate to RNA and DNA molecules within organisms which can lead to somatic and genetic impacts. These can emerge in later generations.^[45]

H³HO has a short biological half-life in the human body of 7 to 14 days, which both reduces the total effects of single-incident ingestion and precludes long-term bioaccumulation of H³HO from the environment.^[40][46] The biological half-life of tritiated water in the human body, which is a measure of body water turn-over, varies with the season. Studies on the biological half-life of occupational radiation workers for free water tritium in a coastal region of Karnataka, India, show that the biological half-life in winter is twice that of the summer.^[46] If tritium exposure is suspected or known, drinking uncontaminated water will help replace the tritium from the body. Increasing sweating, urination or breathing can help the body expel water and thereby the tritium contained in it. However, care should be taken that neither dehydration nor a depletion of the body's electrolytes results, as the health consequences of those things (particularly in the short term) can be more severe than those of tritium exposure.

The examples and perspective in this deal primarily with the United States and do not represent a worldwide view of the subject. You may improve this , discuss the issue on the talk page, or create a new, as appropriate. (January 2022) (Learn how and when to remove this message)

Tritium has leaked from 48 of 65 nuclear sites in the US. In one case, leaking water contained 7.5 microcuries (280 kBq) of tritium per liter, which is 375 times the current EPA limit for drinking water, and 28 times the World Health Organization's recommended limit.^[47] This is equivalent to 0.777 nanograms per litre (5.45×10⁻⁸ gr/imp gal) or roughly 0.8 parts per trillion.

The US Nuclear Regulatory Commission states that in normal operation in 2003, 56 pressurized water reactors released 40,600 curies (1,500,000 GBq) of tritium (maximum: 2,080 Ci (77,000 GBq); minimum: 0.1 Ci (3.7 GBq); average: 725 Ci (26,800 GBq)) and 24 boiling water reactors released 665 Ci (24.6 TBq) (maximum: 174 Ci (6,400 GBq); minimum: 0 Ci; average: 27.7 Ci (1,020 GBq)), in liquid effluents.^[48] 40,600 Ci (1,500,000 GBq) of tritium weigh about 4.207 grams (0.1484 oz).

According to the U.S. Environmental Protection Agency, self-illuminating exit signs improperly disposed in municipal landfills have been found to contaminate waterways.^[49]

The legal limits for tritium in drinking water vary widely from country to country. Some figures are given below:

Tritium drinking water limits by country^[50]

Country	Tritium limit (Bq/L)	Equivalent dose (μSv/year)[b]
Australia	76,103[c]	1,000
Japan	60,000	788.4
Finland	30,000	394.2
World Health Organization	10,000	131.4
Switzerland	10,000	131.4
Russia	7,700	101.18
Canada (Ontario)	7,000	91.98
United States	740	9.72
Norway	100[53]	1.31

The American limit results in a dose of 4.0 millirems (or 40 microsieverts in SI units) per year per EPA regulation 40CFR141, and is based on outdated dose calculation standards of National Bureau of Standards Handbook 69 circa 1963. Four millirem per year is about 1.3% of the natural background radiation (~3 mSv). For comparison, the banana equivalent dose (BED) is set at 0.1 μSv, so the statutory limit in the US is set at 400 BED. Updated dose calculation standards based on International Commission on Radiological Protection Report 30 and used in the NRC Regulation 10CFR20 results in a dose of 0.9 millirem (9 μSv) per year at 740 Bq/L (20 nCi/L).^[40]

This section needs additional citations for verification. Please help improve this article by adding citations to reliable sources in this section. Unsourced material may be challenged and removed. (January 2022) (Learn how and when to remove this message)

Tritiation of drug candidates allows detailed analysis of their absorption and metabolism.^[54] Tritium has also been used for biological radiometric assays, in a process akin to radiocarbon dating. For example, [³H] retinyl acetate was traced through the bodies of rats.^[55]

The beta particles from small amounts of tritium cause chemicals called phosphors to glow. This radioluminescence is used in self-powered lighting devices called betalights, which are used for night illumination of firearm sights, watches, exit signs, map lights, navigational compasses (such as current-use M-1950 U.S. military compasses), knives and a variety of other devices.^[d] As of 2000^[update], commercial demand for tritium is 400 grams (0.88 lb) per year^[11] and the cost is $30,000 per gram ($850,000/oz)^[56] or more.^[57]

Tritium is an important component in nuclear weapons; it is used to enhance the efficiency and yield of fission bombs and the fission stages of hydrogen bombs in a process known as "boosting" as well as in external neutron initiators for such weapons.

These are devices incorporated in nuclear weapons which produce a pulse of neutrons when the bomb is detonated to initiate the fission reaction in the fissionable core (pit) of the bomb, after it is compressed to a critical mass by explosives. Actuated by an ultrafast switch like a krytron, a small particle accelerator drives ions of tritium and deuterium to energies above the 15 keV or so needed for deuterium-tritium fusion and directs them into a metal target where the tritium and deuterium are adsorbed as hydrides. High-energy fusion neutrons from the resulting fusion radiate in all directions. Some of these strike plutonium or uranium nuclei in the primary's pit, initiating a nuclear chain reaction. The quantity of neutrons produced is large in absolute numbers, allowing the pit to quickly achieve neutron levels that would otherwise need many more generations of chain reaction, though still small compared to the total number of nuclei in the pit.

Before detonation, a few grams of tritium–deuterium gas are injected into the hollow "pit" of fissile material. The early stages of the fission chain reaction supply enough heat and compression to start deuterium–tritium fusion; then both fission and fusion proceed in parallel, the fission assisting the fusion by continuing heating and compression, and the fusion assisting the fission with highly energetic (14.1-MeV) neutrons. As the fission fuel depletes and also explodes outward, it falls below the density needed to stay critical by itself, but the fusion neutrons make the fission process progress faster and continue longer than it would without boosting. Increased yield comes overwhelmingly from the increased fission. The energy from the fusion itself is much smaller because the amount of fusion fuel is much smaller. Effects of boosting include:

• increased yield (for the same amount of fission fuel, compared to unboosted)
• the possibility of variable yield by varying the amount of fusion fuel
• allowing the bomb to require a smaller amount of the very expensive fissile material
• eliminating the risk of predetonation by nearby nuclear explosions
• not so stringent requirements on the implosion setup, allowing for a smaller and lighter amount of high explosives to be used

The tritium in a warhead is continually undergoing radioactive decay, becoming unavailable for fusion. Also, its decay product, helium-3, absorbs neutrons. This can offset or reverse the intended effect of the tritium, which was to generate many free neutrons, if too much helium-3 has accumulated. Therefore, boosted bombs need fresh tritium periodically. The estimated quantity needed is 4 grams (0.14 oz) per warhead.^[11] To maintain constant levels of tritium, about 0.20 grams (0.0071 oz) per warhead per year must be supplied to the bomb.

One mole of deuterium-tritium gas contains about 3.0 grams (0.11 oz) of tritium and 2.0 grams (0.071 oz) of deuterium. In comparison, the 20 moles of plutonium in a nuclear bomb consists of about 4.5 kilograms (9.9 lb) of plutonium-239.

Since tritium undergoes radioactive decay, and is also difficult to confine physically, the much larger secondary charge of heavy hydrogen isotopes needed in a true hydrogen bomb uses solid lithium deuteride as its source of deuterium and tritium, producing the tritium in situ during secondary ignition.

During the detonation of the primary fission bomb stage in a thermonuclear weapon (Teller–Ulam staging), the sparkplug, a cylinder of ²³⁵U/²³⁹Pu at the center of the fusion stage(s), begins to fission in a chain reaction, from excess neutrons channeled from the primary. The neutrons released from the fission of the sparkplug split lithium-6 into tritium and helium-4, while lithium-7 is split into helium-4, tritium, and one neutron. As these reactions occur, the fusion stage is compressed by photons from the primary and fission of the ²³⁸U or ²³⁸U/²³⁵U jacket surrounding the fusion stage. Therefore, the fusion stage breeds its own tritium as the device detonates. In the extreme heat and pressure of the explosion, some of the tritium is then forced into fusion with deuterium, and that reaction releases even more neutrons.

Since this fusion process requires an extremely high temperature for ignition, and it produces fewer and less energetic neutrons (only fission, deuterium-tritium fusion, and ⁷
₃Li
splitting are net neutron producers), lithium deuteride is not used in boosted bombs, but rather for multi-stage hydrogen bombs.

Tritium is an important fuel for controlled nuclear fusion in both magnetic confinement and inertial confinement fusion reactor designs. The National Ignition Facility (NIF) uses deuterium–tritium fuel, and the experimental fusion reactor ITER will also do so. The deuterium–tritium reaction is favorable since it has the largest fusion cross section (about 5.0 barns) and it reaches this maximum cross section at the lowest energy (about 65 keV center-of-mass) of any potential fusion fuel. As tritium is very rare on earth, concepts for fusion reactors often include the breeding of tritium. During the operation of envisioned breeder fusion reactors, Breeding blankets, often containing lithium as part of ceramic pebbles, are subjected to neutron fluxes to generate tritium to complete the fuel cycle.^[58]

The Tritium Systems Test Assembly (TSTA) was a facility at the Los Alamos National Laboratory dedicated to the development and demonstration of technologies required for fusion-relevant deuterium–tritium processing.

Tritium can be used in a betavoltaic device to create an atomic battery to generate electricity.

Aside from chlorofluorocarbons, tritium can act as a transient tracer and can "outline" the biological, chemical, and physical paths throughout the world's oceans because of its evolving distribution.^[59] Tritium has thus been used as a tool to examine ocean circulation and ventilation and, for such purposes, is usually measured in tritium units, where 1 TU is defined as 1 tritium atom per 10¹⁸ hydrogen atoms,^[59] equal to about 0.118 Bq/liter.^[60][61][62] As noted earlier, nuclear tests, mainly in the Northern Hemisphere at high latitudes, throughout the late 1950s and early 1960s introduced lots of tritium into the atmosphere, especially the stratosphere. Before these nuclear tests, there were only about 3-4 kg of tritium on the Earth's surface; but these amounts rose by 2-3 orders of magnitude during the post-test period.^[59] Some sources reported natural background levels were exceeded by about 1,000 TU in 1963 and 1964 and the isotope is used in the northern hemisphere to estimate the age of groundwater and construct hydrogeologic simulation models.^[63] Estimated atmospheric levels at the height of weapons testing to approach 1,000 TU and pre-fallout levels of rainwater to be between 5 and 10 TU.^[64] In 1963 Valentia Island Ireland recorded 2,000 TU in precipitation.^[65]

While in the stratosphere (post-test period), the tritium interacted with and oxidized to water molecules and was present in much of the rapidly produced rainfall, making tritium a prognostic tool for studying the evolution and structure of the water cycle as well as the ventilation and formation of water masses in the North Atlantic.^[59]

Bomb-tritium data were used from the Transient Tracers in the Ocean (TTO) program in order to quantify the replenishment and overturning rates for deep water located in the North Atlantic.^[66]

Bomb-tritium also enters the deep ocean around the Antarctic.^[67] Most of the bomb tritiated water (H³HO) throughout the atmosphere can enter the ocean through the following processes:

• precipitation
• vapor exchange
• river runoff

These processes make H³HO a great tracer for time scales of up to a few decades.^[66]

Using the data from these processes for 1981, the 1-TU isosurface lies between 500 and 1,000 meters deep in the subtropical regions and then extends to 1,500–2,000 meters south of the Gulf Stream due to recirculation and ventilation in the upper portion of the Atlantic Ocean.^[59] To the north, the isosurface deepens and reaches the floor of the abyssal plain which is directly related to the ventilation of the ocean floor over 10–20 year time-scales.^[59]

Also evident in the Atlantic Ocean is the tritium profile near Bermuda between the late 1960s and late 1980s. There is a downward propagation of the tritium maximum from the surface (1960s) to 400 meters (1980s), which corresponds to a deepening rate of about 18 meters per year.^[59] There are also tritium increases at 1,500 m depth in the late 1970s and 2,500 m in the middle of the 1980s, both of which correspond to cooling events in the deep water and associated deep water ventilation.^[59]

From a study in 1991, the tritium profile was used as a tool for studying the mixing and spreading of newly formed North Atlantic Deep Water (NADW), corresponding to tritium increases to 4 TU.^[66] This NADW tends to spill over sills that divide the Norwegian Sea from the North Atlantic Ocean and then flows to the west and equatorward in deep boundary currents. This process was explained via the large-scale tritium distribution in the deep North Atlantic between 1981 and 1983.^[66] The sub-polar gyre tends to be freshened (ventilated) by the NADW and is directly related to the high tritium values (>1.5 TU). Also evident was the decrease in tritium in the deep western boundary current by a factor of 10 from the Labrador Sea to the Tropics, which is indicative of loss to ocean interior due to turbulent mixing and recirculation.^[66]

In a 1998 study, tritium concentrations in surface seawater and atmospheric water vapor (10 meters above the surface) were sampled at the following locations: the Sulu Sea, Fremantle Bay, the Bay of Bengal, Penang Bay, and the Strait of Malacca.^[68] Results indicated that the tritium concentration in surface seawater was highest at the Fremantle Bay (about 0.40 Bq/liter), which could be accredited to the mixing of runoff of freshwater from nearby lands due to large amounts found in coastal waters.^[68] Typically, lower concentrations were found between 35 and 45° south, and near the equator. Results also indicated that (in general) tritium has decreased over the years (up to 1997) due to the physical decay of bomb tritium in the Indian Ocean. As for water vapor, the tritium concentration was about one order of magnitude greater than surface seawater concentrations (ranging from 0.46 to 1.15 Bq/L).^[68] Therefore, the water vapor tritium is not affected by the surface seawater concentration; thus, the high tritium concentrations in the vapor were concluded to be a direct consequence of the downward movement of natural tritium from the stratosphere to the troposphere (therefore, the ocean air showed a dependence on latitudinal change).^[68]

In the North Pacific Ocean, the tritium (introduced as bomb tritium in the Northern Hemisphere) spread in three dimensions. There were subsurface maxima in the middle and low latitude regions, which is indicative of lateral mixing (advection) and diffusion processes along lines of constant potential density (isopycnals) in the upper ocean.^[69] Some of these maxima even correlate well with salinity extrema.^[69] In order to obtain the structure for ocean circulation, the tritium concentrations were mapped on 3 surfaces of constant potential density (23.90, 26.02, and 26.81).^[69] Results indicated that the tritium was well-mixed (at 6 to 7 TU) on the 26.81 isopycnal in the subarctic cyclonic gyre and there appeared to be a slow exchange of tritium (relative to shallower isopycnals) between this gyre and the anticyclonic gyre to the south; also, the tritium on the 23.90 and 26.02 surfaces appeared to be exchanged at a slower rate between the central gyre of the North Pacific and the equatorial regions.^[69]

The depth penetration of bomb tritium can be separated into three distinct layers:

Layer 1

Layer 1 is the shallowest layer and includes the deepest, ventilated layer in winter; it has received tritium via radioactive fallout and lost some due to advection and/or vertical diffusion and contains about 28% of the total amount of tritium.^[69]

Layer 2

Layer 2 is below the first layer but above the 26.81 isopycnal and is no longer part of the mixed layer. Its two sources are diffusion downward from the mixed layer and lateral expansions outcropping strata (poleward); it contains about 58% of the total tritium.^[69]

Layer 3

Layer 3 is representative of waters that are deeper than the outcrop isopycnal and can only receive tritium via vertical diffusion; it contains the remaining 14% of the total tritium.^[69]

Nuclear fallout from Cold War weapons testing settled in the United States throughout the Mississippi River System. Tritium concentrations can be used to understand the residence times of continental hydrologic systems (as opposed to the usual oceanic hydrologic systems) which include surface waters such as lakes, streams, and rivers.^[70] Studying these systems can also provide societies and municipals with information for agricultural purposes and overall river water quality.

In a 2004 study, several rivers were taken into account during the examination of tritium concentrations (starting in the 1960s) throughout the Mississippi River Basin: Ohio River (largest input to the Mississippi River flow), Missouri River, and Arkansas River.^[70] The largest tritium concentrations were found in 1963 at all the sampled locations throughout these rivers and correlate well with the peak concentrations in precipitation due to the nuclear bomb tests in 1962. The overall highest concentrations occurred in the Missouri River (1963) and were greater than 1,200 TU while the lowest concentrations were found in the Arkansas River (never greater than 850 TU and less than 10 TU in the mid-1980s).^[70]

Several processes can be identified using the tritium data from the rivers: direct runoff and outflow of water from groundwater reservoirs.^[70] Using these processes, it becomes possible to model the response of the river basins to the transient tritium tracer. Two of the most common models are the following:

Piston-flow approach

tritium signal appears immediately; and

Well-mixed reservoir approach

outflow concentration depends upon the residence time of the basin water^[70]

For the Ohio River, the tritium data indicated that about 40% of the flow was composed of precipitation with residence times of less than one year (in the Ohio basin) and older waters consisted of residence times of about ten years.^[70] Thus, the short residence times (less than one year) corresponded to the "prompt-flow" component of the two-member mixing model. As for the Missouri River, results indicated that residence times were approximately four years with the prompt-flow component being around 10% (these results are due to the series of dams in the area of the Missouri River).^[70]

As for the mass flux of tritium through the main stem of the Mississippi River into the Gulf of Mexico, data indicated that approximately 780 grams of tritium has flowed out of the River and into the Gulf between 1961 and 1997,^[70] an average of 21.7 grams/yr and 7.7 PBq/yr. Current fluxes through the Mississippi River are 1 to 2 grams, per year as opposed to the pre-bomb period fluxes of roughly 0.4 grams per year.^[70]

• Hypertriton
• List of elements facing shortage

• "Annotated bibliography for tritium". Alsos Digital Library. Washington and Lee University. Archived from the original on 14 May 2006. Retrieved 3 March 2022.
• "Nuclear Data Evaluation Lab".
• Review of Risks from Tritium (Report). London, UK: Health Protection Agency. November 2007. RCE-4. Archived from the original on 17 May 2013. Retrieved 3 March 2022.
• Bergeron, Kenneth D. (17 September 2004). Tritium on Ice: The dangerous new alliance of nuclear weapons and nuclear power. MIT Press. ISBN 978-0-262-26172-2.^{[full citation needed]}
• "Tritium production and recovery in the United States in FY2011". Fissile Materials. February 2010.
• "Tritium removal mass transfer coefficient". ans.org.

Lighter: deuterium	Tritium is an isotope of hydrogen	Heavier: hydrogen-4
Decay product of: hydrogen-4	Decay chain of tritium	Decays to: helium-3