Available at Seeed
The ReSpeaker USB 4 Mic Array is the successor of the ReSpeaker USB 6+1 Mic Array. It has better built-in audio processing algorithms than the 6+1 Mic Array, so it has better audio recording quality, although it only has 4 microphones.
- 4 microphones
- 12 RGB LEDs
- USB
- built-in AEC, VAD, DOA, Beamforming and NS
- 16000 sample rate
Audacity is recommended to test audio recording.
On Linux and macOS, the USB 4 Mic Array will just work. On Windows, audio recording and playback will also work without installing a driver. But in order to upgrade the device's firmware or to control LEDs an DSP parameters on Windows, the libusb-win32 driver is required. We use a handy tool - Zadig to install the libusb-win32 driver for both SEEED DFU and SEEED Control (the USB 4 Mic Array has 4 devices on Windows Device Manager).
Make sure that libusb-win32 is selected, not WinUSB or libusbK
The Microphone Array supports USB DFU. We have a python script - dfu.py to do that.
pip install pyusb
python dfu.py --download new_firmware.bin # with sudo if usb permission error
| firmware | channels | note |
|---|---|---|
| 1_channel_firmware.bin | 1 | processed audio for ASR |
| 6_channels_firmware.bin | 6 | channel 0: processed audio for ASR, channel 1-4: 4 microphones' raw data, channel 5: playback |
Note: The flash memory of XVF3000 has updated from 90nm to 65nm, the Jedec ID between the 90nm and 65nm flash memories has a 1-bit different. This will cause the new device not upgradable after you download old firmware(v2.0.0 or below) to an new device. The new firmware(v3.0.0 or above) is already compatible with old device and new device, so we advise customers to use the new firmware when DFU. The new 65nm flash memory device will use new part numbers with a suffix 'A' as the following picture:
| hardware | factory programmed | DFU firmware | outcome | |
|---|---|---|---|---|
| 1 | old device | any | any | DFU succeed, device operates correctly and upgradeable |
| 2 | new device (XVF3000 with a suffix 'A') | 3.0.0 | 3.0.0 or above | DFU succeed, device operates correctly and upgradeable |
| 3 | new device (XVF3000 with a suffix 'A') | 3.0.0 | 2.0.0 or below | DFU succeed, device operates correctly, but not upgradeable |
The USB 4 Mic Array has on-board 12 RGB LEDs and has a variety of light effects. Go to the respeaker/pixel_ring to learn how to use it. The LED control protocol is at respeaker/pixel_ring wiki.
There are some parameters of built-in algorithms to configure. For example, we can turn off Automatic Gain Control (AGC):
python tuning.py AGCONOFF 0i6_firmware.bin
To get the full list parameters, run:
python tuning.py -p
ODAS is a very cool project to perform sound source localization, tracking, separation and post-filtering. Let's have a try!
- get ODAS and build it
sudo apt-get install libfftw3-dev libconfig-dev libasound2-dev
git clone https://github.com/introlab/odas.git --branch=dev
mkdir odas/build
cd odas/build
cmake ..
make
- get ODAS Studio from https://github.com/introlab/odas_web/releases and open it.
The odascore will be at odas/bin/odascore, the config file is at odas.cfg. Change odas.cfg based on your sound card number.
interface: {
type = "soundcard";
card = 1;
device = 0;
}
- upgrade your usb 4 mic array with 6_channels_firmware_6.02dB.bin (or 6_channels_firmware.bin, 6_channels_firmware_12.04dB.bin) which includes 4 channels raw audio data.