Fender Bassman

This article needs additional citations for verification. Please help improve this article by adding citations to reliable sources. Unsourced material may be challenged and removed. Find sources: "Fender Bassman" – news · newspapers · books · scholar · JSTOR (July 2011) (Learn how and when to remove this message)

The Fender Bassman is a series of bass amplifiers introduced by Fender during 1952.^{[citation needed]} Initially intended to amplify bass guitars, musicians used the 5B6 Bassman to amplify other instruments, including electric guitars, harmonicas, and pedal steel guitars. Besides being a popular and important amplifier in its own right, the Bassman also became the foundation on which Marshall and other companies built their high-gain tube amplifiers.^{[citation needed]}

During 1952, the Fender 5B6 Bassman amplifier was introduced as a combo amplifier cabinet that included the amplifier chassis combined with one 15" speaker. The 1952–1954^[1] 5B6 Bassman amplifiers had two 6SC7 or 6SL7GT pre-amp tubes, two 5881 power tubes and a single 5U4G rectifier tube. It was designed to generate 26 watts at an 8-ohm impedance load, and offered a cathode-based bias.^{[citation needed]}

From 1952 through the spring of 1954, Fender produced approximately 660 model 5B6 Bassman amplifiers (serial numbers #0001–0660).^{[citation needed]} The earlier cabinets have been called "TV Front" designs,^[1] with a front panel that had a rectangular grill cloth with rounded corners and looked much like a television of that era. In 1953 the cabinet designs were changed to the so-called "Wide Panel" design, with a 5-inch-wide tweed-covered panel above and below a wider swath of grill cloth. Fender ceased production of 5B6 Bassman amplifiers during the spring of 1954.^{[citation needed]}

During November 1954, Fender introduced the newly designed 5D6 Bassman amplifier offering four 10" speakers and was designed utilizing two rectifier tubes. The 5D6 was a major departure from the earlier 5B6 Fender Bassman model. Designed by Freddie Tavares, longtime R&D man at Fender,^[2] the new circuit included two rectifier tubes and became known as the Dual Rectifier Bassman.^[3][4] Instead of the single 15" speaker, four 10" Jensen Alnico P10R speakers were used. The circuit had two innovations: a fixed bias for the power tubes, which increased power in comparison to the earlier cathode bias design, and a cathodyne phase inverter, using half of the 12AX7 tube and allowing a third gain stage on the other half.^[5]

The first 4x10 Bassman amplifiers started with a batch of prototypes in November and December 1954, model 5D6. No schematic for the 5D6 circuit has ever been found, but Ken Fox and Frank Roy have created a few from originals, and copies are freely available online. Only 11 of these early 5D6 Bassman examples are known to have survived. The lowest serial number known to still exist is 0013 (Frank Roy), 0035 (Albert Talley), 0075 (Jim Cornett), 0077 (Perry Tate), 0089 (Mark Grandfield), 0701, 0745 (Walter Horton), 0769 (Hayes Kolb), 0780 (sold on eBay Nov 2006), 0783, and 0785 (Hayes Kolb) are among those still known to exist.

Fender began making other models with tweed covering, a similar open backed cabinet with a rectangular grill cloth and a narrow (just over an inch wide) tweed covered panel at the top and bottom. Produced from 1954 until 1960, these models are called the "narrow panel" tweed amps .^[5]

Fender introduced the model 5D6 "DK" in November 1954 followed by the 5E6 Bassman Amp during early 1955. The 5E6-A Bassman model was introduced later that year and included some evolutionary improvements.^{[citation needed]} Demand for the tweed Bassman amp grew, so Fender increased production. By the middle of 1957 more than 1,500 examples of the 5E6 series had been sold.^[6]

In July 1957, Fender introduced the model 5F6 Bassman. This model also had four Jensen P10R speakers, but the power supply was redesigned around a single 83 mercury vapor rectifier tube, and a new preamp circuit was introduced that included a three-knob tone stack, with separate controls for treble, midrange and bass. The power amp included a "long tailed pair" phase inverter, an innovation that noticeably increased the "headroom" or clean power output capability of the amplifier. Similar preamp changes were also incorporated in the 5F8 Twin Amp at about the same time, but not on other large-size Fender amps.

During 1958, Fender introduced the model 5F6-A Bassman model. This final 1950s Tweed Bassman model product line included a change from the 83 mercury vapor rectifier tube to the GZ34 rectifier tube, as well as a modification within the Presence control circuit.^[7] During early 1960, Fender began producing the 5F6-A Bassman with Jensen P10Q speakers. The P10Q speakers handle more power and produce better "clean" tones than the earlier P10R speakers. The P10R speakers were shipped within all Fender Bassman amps from late 1954 until early 1960. Many professional music industry analysts have proclaimed the 1950s Fender 4×10 Bassman amps as the greatest guitar amp ever. The first 1954 Fender Tweed 5D6 4×10 circuit generated further Tweed Bassman amplifier development through 1960. Several Bassman models were progressively influenced by the 5D6 through the last Fender Tweed 5F6-A Bassman's circuit design.

The 5F6-A Bassman's design is greatly influential in terms of guitar amplication, as the schematic was directly copied by other manufacturers. Marshall Amplification utilized the circuit unmodified in their JTM45 amplifier during the early 1960s.^[8] The early version of Traynor YBA-1 is also directly copied from 5F6-A circuits, with later versions modified.^[9]

In 1990, Fender began reissuing the 5F6-A Bassman as guitar amp. The first series of the reissue were made at the Corona, California facility, and came equipped with four Eminence-made 10" blue frame AlNiCo speakers, and a solid-state rectifier unit. Later on, production was moved to Ensenada, Baja California, and the model name was altered to "59 Bassman LTD". The LTD came equipped with the original 5AR4 rectifier tube, and four Jensen P10R reissue alnico speakers, which was period correct for the original amp.

In late 1960, Fender introduced a completely redesigned model 6G6 Bassman Amp, using the "piggy-back" design, in which the amplifier chassis is housed in a small cabinet, attached by metal clips to a larger separate speaker enclosure.

The early models were called "Brownface" because of the dark brown color used on the control panel. The 6G6 model was covered in rough Blonde colored Tolex material with Oxblood colored grill cloth. It had a single GZ34 rectifier, two 5881/6L6GC power tubes and four 12AX7 preamp tubes. The output was 50 watts at 8 ohms into a single 12 inch speaker, with a "Tone Ring" baffle in the speaker cabinet. In early 1961, model 6G6-A was introduced with a solid state rectifier replacing the GZ34, and two 12" speakers with a conventional baffle in a slightly larger cabinet (wired in parallel) with a 4-ohm output. In 1962, model 6G6-B was introduced, which incorporated circuit changes but used the same speaker configuration. In 1963 smooth Blonde Tolex covering was used instead of the early rough texture cover, and a light tan grill cloth. In late 1963, Fender changed the cosmetics to what is commonly known as the "blackface" scheme. This amp still had the presence knob and same circuit (designated 6G6-B) as the smooth Blonde Tolex Bassman, but the faceplace was now black, the Tolex was black, and the grillcloth had moved to a silver cloth with black thread. The logo had also transitioned from the flat cast tin Fender with the brown paint in the tail, to a plastic logo with faux chrome and more 3-D shape.

In 1964 Fender introduced the AA864 circuit, and changed the appearance to the "Blackface" design, with black tolex covering and a black painted control panel. Fender was sold to CBS in 1965, and the AA165 circuit was briefly introduced, before being replaced by the AB165 circuit. The "Blackface" design continued until the "Silverface" model was introduced in mid 1967.^[10] Early "Drip-Edge" Silverface Bassmans made in mid 1967 used the same AB165 circuitry as the previous Blackface versions. The Brownface, Blackface, and Silverface "piggyback head" (except the Bassman 10 and 20, which were also combo amplifiers) versions of the 1960s, 1970s, and early 1980s generally followed a trend toward cleaner sound and more headroom.

In 2000, Fender introduced a range of solid-state Fender Bassman combos, the Bassman 25, 60, and 200.^[11] These were joined by the Bassman 100 combo and the tube-powered Bassman 300 head in 2002.^[11] In 2005 all the solid-state combos were replaced with much smaller and lighter, and more powerful models, the Bassman 100, 150, and 250. The Bassman 250 was available with two speaker combinations or as a head only.^[11] These solid-state Bassman amps were discontinued in 2010, however the tube Bassman 300 continued on until 2013.^[11]

In 2009,^[11] Fender introduced the hybrid Fender Bassman TV series with a tube pre-amp and solid-state power amp.^[12] These were available as the Ten (150W 10" combo), Twelve (150W 12" combo), Fifteen (350W 15" combo), and the Duo Ten (350W 2 × 10" combo).^[12]

• Super Bassman (1969–1971) – one speaker cabinet
• Super Bassman II (1969–1972) – two speaker cabinets
• Bassman 10 (1972–1982) – Silverface combo – four 10" speakers, 50 Watts/RMS (models produced after 1977 came with a three-band EQ on the Bass channel and 75 Watts/RMS with ultra-linear output section).
• Bassman 50 (1972–1977) – Silverface piggyback head – two 15" speakers, 50 Watts/RMS – Same specs as the original silverface Bassman heads produced between 1968 and 1972, except for the addition of a tailless amp decal and an AC568 circuit.
• Bassman 100 (1972–1977) – Silverface piggyback head – four 12" speakers, 100 Watts/RMS.
• Bassman 135 (1978–1983) – Silverface piggyback head – Same as the Bassman 100, with 135 Watts/RMS, ultra-linear output section and a three band EQ on the Bass channel.
• Bassman 70 (1977–1983) – Silverface piggyback head – Same as the Bassman 50, with 70 Watts/RMS, ultra-linear output section and a master volume control.
• Bassman 20 (1982–1983)^[11] – Blackface combo – one 15" speaker
• '59 Bassman (1990–2003) – 5F6-A reissue^[13]
• '59 Bassman LTD (Vintage Reissue Series) (2004–present) – 5F6-A reissue
• Bassman 25 (2000–2005)^[11] – one 10" speaker, 25 Watts/RMS solid state.^[11]
• Bassman 60 (2000–2005)^[11] – one 12" speaker, one horn, 60 Watts/RMS solid state.^[11]
• Bassman 200 (2000–2005)^[11] – one 15" speaker, one compression driver, 200 Watts/RMS solid state.^[11]
• Bassman 100 (2002–2005)^[11] – one 15" speaker, one piezo horn, 100 Watts/RMS solid-state.^[11]
• Bassman 100 (2005–2010)^[11] – one 10" speaker, one piezo horn, 100 Watts/RMS solid-state.^[11]
• Bassman 150 (2005–2010)^[11] – one 12" speaker, one piezo horn, 150 Watts/RMS solid-state.^[11]
• Bassman 250 (2005–2010)^[11] – one 15" speaker, or two 10" speakers, or head only, 250Watts/RMS solid state.^[11]
• Bassman 300 (2002–2013)^[11] – head only, 300W tube, for use with Bassman 410 or 215 cabinets.^[11]
• Bassman 400 (200?–) – two 10" and one horn, or head only(400H), 350 Watts/RMS at 4 Ohms, solid state.^[11]
• Bassman 1200 (200?–) – head only, 1200 Watts at 2 Ohms, 800 Watts at 4 Ohms, solid state.^[11]

• Kelly, Martin; Foster, Terry; Kelly, Paul (2010). Fender: The Golden Age 1946–1970. London & New York: Cassell. ISBN 978-1-84403-666-0.
• Wheeler, Tom (2007). The Soul of Tone. Milwaukee: Hal Leonard. ISBN 978-0-634-05613-0.