List of ISO standards 10000–11999

This is a list of published^{[Note 1]} International Organization for Standardization (ISO) standards and other deliverables.^{[Note 2]} For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.^[1]

The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC 1) have been made freely and publicly available.^[2]

• ISO/IEC TR 10000 Information technology – Framework and taxonomy of International Standardized Profiles
  • ISO/IEC TR 10000-1:1998 Part 1: General principles and documentation framework
  • ISO/IEC TR 10000-2:1998 Part 2: Principles and Taxonomy for OSI Profiles
  • ISO/IEC TR 10000-3:1998 Part 3: Principles and Taxonomy for Open System Environment Profiles
• ISO 10001:2007 Quality management – Customer satisfaction – Guidelines for codes of conduct for organizations
• ISO 10002:2014 Quality management – Customer satisfaction – Guidelines for complaints handling in organizations
• ISO 10003:2007 Quality management – Customer satisfaction – Guidelines for dispute resolution external to organizations
• ISO 10004:2008 Quality management – Customer satisfaction – Guidelines for monitoring and measuring
• ISO 10005:2005 Quality management systems – Guidelines for quality plans
• ISO 10006:2003 Quality management systems – Guidelines for quality management in projects
• ISO 10007:2017 Quality management systems – Guidelines for configuration management
• ISO 10008:2013 Quality management – Customer satisfaction – Guidelines for business-to-consumer electronic commerce transactions
• ISO 10012:2003 Measurement management systems – Requirements for measurement processes and measuring equipment
• ISO/TR 10013:2001 Guidelines for quality management system documentation
• ISO 10014:2006 Quality management – Guidelines for realizing financial and economic benefits
• ISO 10015:1999 Quality management – Guidelines for training
• ISO/TR 10017:2003 Guidance on statistical techniques for ISO 9001:2000
• ISO 10018:2012 Quality management – Guidelines on people involvement and competence
• ISO 10019:2005 Guidelines for the selection of quality management system consultants and use of their services
• ISO/IEC 10021 Information technology – Message Handling Systems (MHS)
• ISO/IEC 10022:1996 Information technology – Open Systems Interconnection – Physical Service Definition
• ISO/IEC 10026 Information technology – Open Systems Interconnection – Distributed Transaction Processing
  • ISO/IEC 10026-1:1998 Part 1: OSI TP Model
  • ISO/IEC 10026-2:1998 Part 2: OSI TP Service
  • ISO/IEC 10026-3:1998 Part 3: Protocol specification
  • ISO/IEC 10026-4:1995 Protocol Implementation Conformance Statement (PICS) proforma
  • ISO/IEC 10026-5:1998 Part 5: Application context proforma and guidelines when using OSI TP
  • ISO/IEC 10026-6:1995 Part 6: Unstructured Data Transfer
• ISO/IEC 10027:1990 Information technology – Information Resource Dictionary System (IRDS) framework
• ISO/IEC 10028:1993 Information technology – Telecommunications and information exchange between systems – Definition of the relaying functions of a Network layer intermediate system
• ISO/IEC 10030:1995 Information technology – Telecommunications and information exchange between systems – End System Routing Information Exchange Protocol for use in conjunction with ISO/IEC 8878
• ISO/IEC TR 10032:2003 Information technology – Reference Model of Data Management
• ISO/IEC TR 10034:1990 Guidelines for the preparation of conformity clauses in programming language standards
• ISO/IEC 10035 Information technology – Open Systems Interconnection – Connectionless protocol for the Association Control Service Element
  • ISO/IEC 10035-2:1995 Protocol Implementation Conformance Statement (PICS) proforma
• ISO/IEC 10036:1996 Information technology - Font information interchange - Procedures for registration of font-related identifiers
• ISO/IEC 10040:1998 Information technology – Open Systems Interconnection – Systems management overview
• ISO 10052:2004 Acoustics – Field measurements of airborne and impact sound insulation and of service equipment sound – Survey method
• ISO 10055:1996 Mechanical vibration - Vibration testing requirements for shipboard equipment and machinery components
• ISO 10075 Ergonomic principles related to mental workload
  • ISO 10075-1:2017 Part 1: General issues and concepts, terms and definitions
• ISO 10077 Thermal performance of windows, doors and shutters – Calculation of thermal transmittance
• ISO 10079 Medical suction equipment
  • ISO 10079-1:2015 Part 1: Electrically powered suction equipment
  • ISO 10079-2:2014 Part 2: Manually powered suction equipment
  • ISO 10079-3:2014 Part 3: Suction equipment powered from a vacuum or positive pressure gas source
• ISO/IEC 10089:1991 Information technology – 130 mm rewritable optical disk cartridge for information interchange
• ISO/IEC 10090:1992 Information technology – 90 mm optical disk cartridges, rewritable and read only, for data interchange
• ISO/IEC TR 10091:1995 Information technology – Technical aspects of 130 mm optical disk cartridge write-once recording format
• ISO 10110 Optics and photonics – Preparation of drawings for optical elements and systems^{[Note 3]}
  • ISO 10110-1:2006 Part 1: General
  • ISO 10110-2:1996 Part 2: Material imperfections – Stress birefringence
  • ISO 10110-3:1996 Part 3: Material imperfections – Bubbles and inclusions
  • ISO 10110-4:1997 Part 4: Material imperfections – Inhomogeneity and striae
  • ISO 10110-5:2015 Part 5: Surface form tolerances
  • ISO 10110-6:2015 Part 6: Centring tolerances
  • ISO 10110-7:2017 Part 7: Surface imperfections
  • ISO 10110-8:2010 Part 8: Surface texture; roughness and waviness
  • ISO 10110-9:2016 Part 9: Surface treatment and coating
  • ISO 10110-10:2004 Part 10: Table representing data of optical elements and cemented assemblies
  • ISO 10110-11:2016 Part 11: Non-toleranced data
  • ISO 10110-12:2007 Part 12: Aspheric surfaces
  • ISO 10110-14:2007 Part 14: Wavefront deformation tolerance
  • ISO 10110-17:2004 Part 17: Laser irradiation damage threshold
  • ISO 10110-19:2015 Part 19: General description of surfaces and components
• ISO 10112:1991 Damping materials – Graphical presentation of the complex modulus
• ISO/IEC 10116 Information technology – Security techniques – Modes of operation for an n-bit block cipher
• ISO/IEC 10118 Information technology – Security techniques – Hash-functions
  • ISO/IEC 10118-1:2016 Part 1: General
  • ISO/IEC 10118-2:2010 Part 2: Hash-functions using an n-bit block cipher
  • ISO/IEC 10118-3:2004 Part 3: Dedicated hash-functions
  • ISO/IEC 10118-4:1998 Part 4: Hash-functions using modular arithmetic
• ISO 10132:1993 Textiles – Textured filament yarn – Definitions
• ISO 10135:2007 Geometrical product specifications (GPS) – Drawing indications for moulded parts in technical product documentation (TPD)
• ISO/IEC 10149:1995 Information technology - Data interchange on read-only 120 mm optical data disks (CD-ROM)
• ISO 10159:2011 Health informatics – Messages and communication – Web access reference manifest
• ISO 10160:2015 Information and documentation – Open Systems Interconnection – Interlibrary Loan Application Service Definition
• ISO 10161 Information and documentation – Open Systems Interconnection – Interlibrary Loan Application Protocol Specification
  • ISO 10161-1:2014 Part 1: Protocol specification
  • ISO 10161-2:2014 Part 2: Protocol implementation conformance statement (PICS) proforma
• ISO/IEC 10164 Information technology – Open Systems Interconnection – Systems Management
  • ISO/IEC 10164-1:1993 Object Management Function
  • ISO/IEC 10164-2:1993 State Management Function
  • ISO/IEC 10164-3:1993 Attributes for representing relationships
  • ISO/IEC 10164-4:1992 Alarm reporting function
  • ISO/IEC 10164-5:1993 Event Report Management Function
  • ISO/IEC 10164-6:1993 Log control function
  • ISO/IEC 10164-7:1992 Security alarm reporting function
  • ISO/IEC 10164-8:1993 Security audit trail function
  • ISO/IEC 10164-9:1995 Objects and attributes for access control
  • ISO/IEC 10164-10:1995 Usage metering function for accounting purposes
  • ISO/IEC 10164-11:1994 Metric objects and attributes
  • ISO/IEC 10164-12:1994 Test Management Function
  • ISO/IEC 10164-13:1995 Summarization Function
  • ISO/IEC 10164-14:1996 Confidence and diagnostic test categories
  • ISO/IEC 10164-15:2002 Scheduling function
  • ISO/IEC 10164-16:1997 Management knowledge management function
  • ISO/IEC 10164-17:1996 Change over function
  • ISO/IEC 10164-18:1997 Software management function
  • ISO/IEC 10164-19:1998 Management domain and management policy management function
  • ISO/IEC 10164-20:1999 Time management function
  • ISO/IEC 10164-21:1998 Command sequencer for Systems Managenment
  • ISO/IEC 10164-22:2000 Response time monitoring
• ISO/IEC 10165 Information technology – Open Systems Interconnection – Structure of management information^{[Note 3]}
  • ISO/IEC 10165-1:1993 Management Information Model
  • ISO/IEC 10165-2:1992 Definition of management information
  • ISO/IEC 10165-4:1992 Part 4: Guidelines for the definition of managed objects
  • ISO/IEC 10165-5:1994 Generic management information
  • ISO/IEC 10165-6:1997 Requirements and guidelines for implementation conformance statement proformas associated with OSI management
  • ISO/IEC 10165-7:1996 General relationship model
  • ISO/IEC 10165-8:2000 Managed objects for supporting upper layers
  • ISO/IEC 10165-9:2000 Systems management application layer managed objects
• ISO/IEC 10166 Information technology – Text and office systems – Document Filing and Retrieval (DFR)
  • ISO/IEC 10166-1:1991 Part 1: Abstract service definition and procedures
  • ISO/IEC 10166-2:1991 Part 2: Protocol specification
• ISO/IEC TR 10171:2000 Information technology – Telecommunications and information exchange between systems – List of standard data link layer protocols that utilize high-level data link control (HDLC) classes of procedures, list of standard XID format identifiers, list of standard mode-setting information field format identifiers, and list of standard user-defined parameter set identification values
• ISO/IEC 10173:1998 Information technology – Telecommunications and information exchange between systems – Interface connector and contact assignments for ISDN primary rate access connector located at reference points S and T
• ISO/IEC 10175 Information technology – Text and office systems – Document Printing Application (DPA)
  • ISO/IEC 10175-1:1996 Part 1: Abstract service definition and procedures
  • ISO/IEC 10175-2:1996 Part 2: Protocol specification
  • ISO/IEC 10175-3:2000 Part 3: Management abstract service definitions and procedures
• ISO/IEC TR 10176:2003 Information technology - Guidelines for the preparation of programming language standards
• ISO/IEC 10177:1993 Information technology – Telecommunications and information exchange between systems – Provision of the connection-mode Network internal layer service by intermediate systems using ISO/IEC 8208, the X.25 Packet Layer Protocol
• ISO/IEC 10179:1996 Information technology – Processing languages – Document Style Semantics and Specification Language (DSSSL)
• ISO/IEC 10180:1995 Information technology - Processing languages - Standard Page Description Language (SPDL)
• ISO/IEC 10181 Information technology - Open Systems Interconnection - Security frameworks for open systems
  • ISO/IEC 10181-1:1996 Overview
  • ISO/IEC 10181-2:1996 Authentication framework
  • ISO/IEC 10181-3:1996 Access control framework
  • ISO/IEC 10181-4:1997 Non-repudiation framework
  • ISO/IEC 10181-5:1996 Confidentiality framework
  • ISO/IEC 10181-6:1996 Integrity framework
  • ISO/IEC 10181-7:1996 Security audit and alarms framework
• ISO/IEC TR 10182:2016 Information technology - Programming languages, their environments and system software interfaces - Guidelines for language bindings
• ISO/IEC TR 10183 Information technology – Text and office systems – Office Document Architecture (ODA) and interchange format – Technical Report on ISO 8613 implementation testing
  • ISO/IEC TR 10183-1:1993 Part 1: Testing methodology
  • ISO/IEC TR 10183-2:1993 Part 2: Framework for abstract test cases
• ISO/IEC 10192 Information technology - Home Electronic System (HES) interfaces
  • ISO/IEC 10192-1:2002 Part 1: Universal Interface (UI) Class 1
  • ISO/IEC TR 10192-2:2000 Part 2: Simple Interfaces Type 1
• ISO/IEC 10206:1991 Information technology – Programming languages – Extended Pascal
• ISO 10209:2012 Technical product documentation - Vocabulary - Terms relating to technical drawings, product definition and related documentation
• ISO 10211 Thermal bridges in building construction – Heat flows and surface temperatures – Detailed calculations
• ISO 10218 Robots and robotic devices – Safety requirements for industrial robots
• ISO 10241 Terminological entries in standards
  • ISO 10241-1:2011 Part 1: General requirements and examples of presentation
  • ISO 10241-2:2012 Part 2: Adoption of standardized terminological entries
• ISO 10243:2010 Tools for pressing – Compression springs with rectangular section – Housing dimensions and colour coding
• ISO 10244:2010 Document management - Business process baselining and analysis
• ISO 10254:2016 Air cargo and ground equipment – Vocabulary
• ISO/TR 10255:2009 Document management applications - Optical disk storage technology, management and standards
• ISO 10263 Earth-moving machinery – Operator enclosure environment
  • ISO 10263-1:2009 Part 1: Terms and definitions
• ISO 10265:2008 Earth-moving machinery - Crawler machines - Performance requirements and test procedures for braking systems
• ISO 10272 Microbiology of the food chain – Horizontal method for detection and enumeration of Campylobacter spp.
  • ISO 10272-1:2017 Part 1: Detection method
  • ISO 10272-2:2017 Part 2: Colony-count technique
• ISO 10273:2017 Microbiology of the food chain - Horizontal method for the detection of pathogenic Yersinia enterocolitica
• ISO/IEC 10279:1991 Information technology – Programming languages – Full BASIC
• ISO 10284:1997 Cinematography - Graphical symbols - Description
• ISO 10286:2015 Gas cylinders - Terminology
• ISO 10302 Acoustics – Measurement of airborne noise emitted and structure-borne vibration induced by small air-moving devices
  • ISO 10302-1:2011 Part 1: Airborne noise measurement
  • ISO 10302-2:2011 Part 2: Structure-borne vibration measurements
• ISO 10303 Industrial automation systems and integration – Product data representation and exchange
• ISO 10316:1990 Shipbuilding — Class B magnetic compasses — Tests and certification [Withdrawn: replaced by ISO 25862]
• ISO 10318 Geosynthetics
  • ISO 10318-1:2015 Part 1: Terms and definitions
  • ISO 10318-2:2015 Part 2: Symbols and pictograms
• ISO 10322 Ophthalmic optics – Semi-finished spectacle lens blanks
  • ISO 10322-1:2016 Part 1: Specifications for single-vision and multifocal lens blanks
  • ISO 10322-2:2016 Part 2: Specifications for progressive-power and degressive-power lens blanks
• ISO 10324:1997 Information and documentation - Holdings statements - Summary level
• ISO 10328:2016 Prosthetics – Structural testing of lower-limb prostheses – Requirements and test methods
• ISO 10334:1994 Implants for surgery – Malleable wires for use as sutures and other surgical applications
• ISO 10341:2012 Ophthalmic instruments – Refractor heads
• ISO 10342:2010 Ophthalmic instruments – Eye refractometers
• ISO 10343:2014 Ophthalmic instruments – Ophthalmometers
• ISO 10360 Geometrical Product Specifications (GPS) - Acceptance and reverification tests for coordinate measuring systems (CMS)^{[Note 3]}
  • ISO 10360-1:2000 Part 1: Vocabulary
  • ISO 10360-2:2009 Part 2: CMMs used for measuring linear dimensions
  • ISO 10360-3:2000 Part 3: CMMs with the axis of a rotary table as the fourth axis
  • ISO 10360-4:2000 Part 4: CMMs used in scanning measuring mode
  • ISO 10360-5:2010 Part 5: CMMs using single and multiple stylus contacting probing systems
  • ISO 10360-6:2001 Part 6: Estimation of errors in computing Gaussian associated features
  • ISO 10360-7:2011 Part 7: CMMs equipped with imaging probing systems
  • ISO 10360-8:2013 Part 8: CMMs with optical distance sensors
  • ISO 10360-9:2013 Part 9: CMMs with multiple probing systems
  • ISO 10360-10:2016 Part 10: Laser trackers for measuring point-to-point distances
  • ISO 10360-12:2016 Part 12: Articulated arm coordinate measurement machines (CMM)
• ISO/IEC 10367:1991 Information technology - Standardized coded graphic character sets for use in 8-bit codes
• ISO/IEC 10373 Identification cards – Test methods
  • ISO/IEC 10373-1:2006 Part 1: General characteristics
  • ISO/IEC 10373-2:2015 Part 2: Cards with magnetic stripes
  • ISO/IEC 10373-3:2010 Part 3: Integrated circuit cards with contacts and related interface devices
  • ISO/IEC 10373-5:2014 Part 5: Optical memory cards
  • ISO/IEC 10373-6:2016 Part 6: Proximity cards
  • ISO/IEC 10373-7:2008 Part 7: Vicinity cards
  • ISO/IEC 10373-8:2011 Part 8: USB-ICC
  • ISO/IEC 10373-9:2011 Part 9: Optical memory cards - Holographic recording method
• ISO 10377:2013 Consumer product safety – Guidelines for suppliers
• ISO 10380 Pipework — Corrugated metal hoses and hose assemblies
• ISO 10383:2012 Securities and related financial instruments – Codes for exchanges and market identification (MIC)
• ISO 10386:1994 Ferroboron - Specification and conditions of delivery
• ISO 10387:1994 Metal chrome - Specification and conditions of delivery
• ISO 10393:2013 Consumer product recall – Guidelines for suppliers
• ISO 10456 Building materials and products – Hygrothermal properties – Tabulated design values and procedures for determining declared and design thermal values
• ISO 10487 Passenger cars – Connections for car radios^{[Note 3]}
• ISO 10494:1993 Gas turbines and gas turbine sets – Measurement of emitted airborne noise – Engineering/survey method
• ISO/IEC 10514 Information technology - Programming languages
  • ISO/IEC 10514-1:1996 Part 1: Modula-2, Base Language
  • ISO/IEC 10514-2:1998 Part 2: Generics Modula-2
  • ISO/IEC 10514-3:1998 Part 3: Object Oriented Modula-2
• ISO 10524 Pressure regulators for use with medical gases
  • ISO 10524-1:2006 Part 1: Pressure regulators and pressure regulators with flow-metering devices
  • ISO 10524-2:2005 Part 2: Manifold and line pressure regulators
  • ISO 10524-3:2005 Part 3: Pressure regulators integrated with cylinder valves
  • ISO 10524-4:2008 Part 4: Low-pressure regulators
• ISO 10534 Acoustics – Determination of sound absorption coefficient and impedance in impedance tubes
  • ISO 10534-1:1996 Part 1: Method using standing wave ratio
  • ISO 10534-2:1998 Part 2: Transfer-function method
• ISO/IEC 10536 Identification cards – Contactless integrated circuit(s) cards – Close-coupled cards^{[Note 3]}
  • ISO/IEC 10536-1:2000 Part 1: Physical characteristics
  • ISO/IEC 10536-2:1995 Part 2: Dimensions and location of coupling areas
  • ISO/IEC 10536-3:1996 Part 3: Electronic signals and reset procedures
• ISO/IEC 10538:1991 Information technology - Control functions for text communication
• ISO 10555 Intravascular catheters – Sterile and single-use catheters
  • ISO 10555-1:2013 Part 1: General requirements
  • ISO 10555-3:2013 Part 3: Central venous catheters
  • ISO 10555-4:2013 Part 4: Balloon dilatation catheters
  • ISO 10555-5:2013 Part 5: Over-needle peripheral catheters
  • ISO 10555-6:2015 Part 6: Subcutaneous implanted ports
• ISO/IEC 10561:1999 Information technology - Office equipment - Printing devices - Method for measuring throughput - Class 1 and Class 2 printers
• ISO 10567:2007 Earth-moving machinery - Hydraulic excavators - Lift capacity
• ISO 10576 Statistical methods - Guidelines for the evaluation of conformity with specified requirements
  • ISO 10576-1:2003 Part 1: General principles
• ISO 10579:2010 Geometrical product specifications (GPS) – Dimensioning and tolerancing – Non-rigid parts
• ISO 10585:1996 Information and documentation - Armenian alphabet coded character set for bibliographic information interchange
• ISO 10586:1996 Information and documentation - Georgian alphabet coded character set for bibliographic information interchange
• ISO/IEC 10588:1993 Information technology – Use of X.25 Packet Layer Protocol in conjunction with X.21/X.21 bis to provide the OSI connection-mode Network Service
• ISO/IEC 10589:2002 Information technology – Telecommunications and information exchange between systems – Intermediate System to Intermediate System intra-domain routeing information exchange protocol for use in conjunction with the protocol for providing the connectionless-mode network service (ISO 8473)
• ISO 10625:2005 Equipment for crop protection – Sprayer nozzles – Colour coding for identification
• ISO 10628 Flow diagrams for process plants
• ISO/IEC 10641:1993 Information technology - Computer graphics and image processing - Conformance testing of implementations of graphics standards
• ISO/IEC 10646:2020 Information technology — Universal Coded Character Set (UCS)
• ISO 10651 Lung ventilators for medical use – Particular requirements for basic safety and essential performance^{[Note 3]}
  • ISO 10651-1:1993 Part 1: Requirements
  • ISO 10651-2:1996 Part 2: Particular requirements for home care ventilators
  • ISO 10651-3:1997 Part 3: Particular requirements for emergency and transport ventilators
  • ISO 10651-4:2002 Part 4: Particular requirements for operator-powered resuscitators
  • ISO 10651-5:2006 Part 5: Gas-powered emergency resuscitators
  • ISO 10651-6:2004 Part 6: Home-care ventilatory support devices
• ISO 10656:2016 Resistance welding equipment – Transformers – Integrated transformers for welding guns
• ISO 10664 Hexalobular internal driving feature for bolts and screws – Torx screw head
• ISO 10667 Assessment service delivery – Procedures and methods to assess people in work and organizational settings
  • ISO 10667-1:2011 Part 1: Requirements for the client
  • ISO 10667-2:2011 Part 2: Requirements for service providers
• ISO 10668:2010 Brand valuation - Requirements for monetary brand valuation
• ISO 10685 Ophthalmic optics – Spectacle frames and sunglasses electronic catalogue and identification
  • ISO 10685-1:2011 Part 1: Product identification and electronic catalogue product hierarchy
  • ISO 10685-2:2016 Part 2: Commercial information
  • ISO 10685-3:2012 Part 3: Technical information
• ISO 10703:2007 Water quality - Determination of the activity concentration of radionuclides - Method by high resolution gamma-ray spectrometry
• ISO 10705 Water quality – Detection and enumeration of bacteriophages
  • ISO 10705-1:1995 Part 1: Enumeration of F-specific RNA bacteriophages
  • ISO 10705-2:2000 Part 2: Enumeration of somatic coliphages
  • ISO 10705-3:2003 Part 3: Validation of methods for concentration of bacteriophages from water
  • ISO 10705-4:2001 Part 4: Enumeration of bacteriophages infecting Bacteroides fragilis
• ISO 10711:2012 Intelligent Transport Systems – Interface Protocol and Message Set Definition between Traffic Signal Controllers and Detectors
• ISO 10718:2015 Cork stoppers – Characterization of a low-in-germs stopper, through the enumeration of colony-forming units of yeasts, moulds and bacteria, capable of both being extracted and growing in alcoholic medium
• ISO 10725:2000 Acceptance sampling plans and procedures for the inspection of bulk materials
• ISO/IEC 10728:1993 Information technology – Information Resource Dictionary System (IRDS) Services Interface
• ISO/IEC 10731:1994 Information technology - Open Systems Interconnection - Basic Reference Model - Conventions for the definition of OSI services
• ISO/IEC 10732:1993 Information technology – Use of X.25 Packet Layer Protocol to provide the OSI connection-mode Network Service over the telephone network
• ISO/IEC 10733:1998 Information technology – Elements of management information related to the OSI Network Layer
• ISO/IEC 10736:1995 Information technology – Telecommunications and information exchange between systems – Transport layer security protocol
• ISO/IEC 10737:1998 Information technology – Elements of management information related to OSI Transport layer
• ISO/IEC 10741 Information technology – User system interfaces – Dialogue interaction
  • ISO/IEC 10741-1:1995 Part 1: Cursor control for text editing
• ISO/IEC 10742:1994 Information technology – Telecommunications and information exchange between systems – Elements of management information related to OSI Data Link Layer standards
• ISO/IEC 10744:1997 Information technology - Hypermedia/Time-based Structuring Language (HyTime)
• ISO/IEC 10745:1995 Information technology - Open Systems Interconnection - Upper layers security model
• ISO/IEC 10746 Information technology—Open Distributed Processing—Reference model
  • ISO/IEC 10746-1:1998 Overview
  • ISO/IEC 10746-2:2009 Foundations
  • ISO/IEC 10746-3:2009 Architecture
  • ISO/IEC 10746-4:1998 Architectural semantics
• ISO/IEC 10747:1994 Information technology – Telecommunications and information exchange between systems – Protocol for exchange of inter-domain routeing information among intermediate systems to support forwarding of ISO 8473 PDUs
• ISO 10754:1996 Information and documentation - Extension of the Cyrillic alphabet coded character set for non-Slavic languages for bibliographic information interchange
• ISO/IEC 10779:2008 Information technology – Office equipment accessibility guidelines for elderly persons and persons with disabilities
• ISO/HL7 10781:2015 Health Informatics – HL7 Electronic Health Records-System Functional Model, Release 2 (EHR FM)
• ISO 10782 Definitions and attributes of data elements for control and monitoring of textile processes
  • ISO 10782-1:1998 Part 1: Spinning, spinning preparatory and related processes
• ISO 10790:2015 Measurement of fluid flow in closed conduits – Guidance to the selection, installation and use of Coriolis flowmeters (mass flow, density and volume flow measurements)
• ISO 10795:2011 Space systems – Programme management and quality – Vocabulary
• ISO/TS 10797:2012 Nanotechnologies – Characterization of single-wall carbon nanotubes using transmission electron microscopy
• ISO/TS 10798:2011 Nanotechnologies – Characterization of single-wall carbon nanotubes using scanning electron microscopy and energy dispersive X-ray spectrometry analysis
• ISO 10801:2010 Nanotechnologies – Generation of metal nanoparticles for inhalation toxicity testing using the evaporation/condensation method
• ISO 10807:1994 Pipework - Corrugated flexible metallic hose assemblies for the protection of electrical cables in explosive atmospheres
• ISO 10808:2010 Nanotechnologies – Characterization of nanoparticles in inhalation exposure chambers for inhalation toxicity testing
• ISO/TS 10811 Mechanical vibration and shock – Vibration and shock in buildings with sensitive equipment
  • ISO/TS 10811-1:2000 Part 1: Measurement and evaluation
  • ISO/TS 10811-2:2000 Part 2: Classification
• ISO 10813 Vibration generating machines – Guidance for selection
  • ISO 10813-1:2004 Part 1: Equipment for environmental testing
• ISO 10815:2016 Mechanical vibration – Measurement of vibration generated internally in railway tunnels by the passage of trains
• ISO 10816 Mechanical vibration - Evaluation of machine vibration by measurements on non-rotating parts
  • ISO 10816-1:1995 Part 1: General guidelines
  • ISO 10816-2:2009 Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
  • ISO 10816-3:2009 Part 3: Industrial machines with nominal power above 15 kW and nominal speeds between 120 r/min and 15 000 r/min when measured in situ
  • ISO 10816-4:2009 Part 4: Gas turbine sets with fluid-film bearings
  • ISO 10816-5:2000 Part 5: Machine sets in hydraulic power generating and pumping plants
  • ISO 10816-6:1995 Part 6: Reciprocating machines with power ratings above 100 kW
  • ISO 10816-7:2009 Part 7: Rotodynamic pumps for industrial applications, including measurements on rotating shafts
  • ISO 10816-8:2014 Part 8: Reciprocating compressor systems
  • ISO 10816-21:2015 Part 21: Horizontal axis wind turbines with gearbox
• ISO 10817 Rotating shaft vibration measuring systems
  • ISO 10817-1:1998 Part 1: Relative and absolute sensing of radial vibration
• ISO 10825:1995 Gears - Wear and damage to gear teeth - Terminology
• ISO 10843:1997 Acoustics – Methods for the description and physical measurement of single impulses or series of impulses
• ISO 10844:2014 Acoustics – Specification of test tracks for measuring noise emitted by road vehicles and their tyres
• ISO 10846 Acoustics and vibration – Laboratory measurement of vibro-acoustic transfer properties of resilient elements
  • ISO 10846-1:2008 Part 1: Principles and guidelines
  • ISO 10846-2:2008 Part 2: Direct method for determination of the dynamic stiffness of resilient supports for translatory motion
  • ISO 10846-3:2002 Part 3: Indirect method for determination of the dynamic stiffness of resilient supports for translatory motion
  • ISO 10846-4:2003 Part 4: Dynamic stiffness of elements other than resilient supports for translatory motion
  • ISO 10846-5:2008 Part 5: Driving point method for determination of the low-frequency transfer stiffness of resilient supports for translatory motion
• ISO 10847:1997 Acoustics – In-situ determination of insertion loss of outdoor noise barriers of all types
• ISO/IEC 10859:1997 Information technology - 8-bit backplane interface: STEbus and mechanical core specifications for microcomputers
• ISO/IEC 10861:1994 Information technology - Microprocessor systems - High-performance synchronous 32-bit bus: MULTIBUS II
• ISO/TS 10867:2010 Nanotechnologies – Characterization of single-wall carbon nanotubes using near infrared photoluminescence spectroscopy
• ISO/TS 10868:2017 Nanotechnologies – Characterization of single-wall carbon nanotubes using ultraviolet-visible-near infrared (UV-Vis-NIR) absorption spectroscopy
• ISO 10878:2013 Non-destructive testing - Infrared thermography - Vocabulary
• ISO/IEC 10885:1993 Information technology - 356 mm optical disk cartridge for information interchange - Write once
• ISO/IEC 10918 Information technology - Digital compression and coding of continuous-tone still images
• ISO/TR 10929:2012 Nanotechnologies – Characterization of multiwall carbon nanotube (MWCNT) samples
• ISO 10934 Optics and optical instruments - Vocabulary for microscopy
  • ISO 10934-1:2002 Part 1: Light microscopy
  • ISO 10934-2:2007 Part 2: Advanced techniques in light microscopy
• ISO 10936 Optics and photonics – Operation microscopes
  • ISO 10936-1:2017 Part 1: Requirements and test methods
  • ISO 10936-2:2010 Part 2: Light hazard from operation microscopes used in ocular surgery
• ISO 10938:2016 Ophthalmic optics – Chart displays for visual acuity measurement – Printed, projected and electronic
• ISO 10939:2017 Ophthalmic instruments – Slit-lamp microscopes
• ISO 10940:2009 Ophthalmic instruments – Fundus cameras
• ISO 10942:2006 Ophthalmic instruments – Direct ophthalmoscopes
• ISO 10943:2011 Ophthalmic instruments – Indirect ophthalmoscopes
• ISO 10944:2009 Ophthalmic instruments – Synoptophores
• ISO 10957:2009 Information and documentation – International standard music number (ISMN)
• ISO 10962:2015 Securities and related financial instruments – Classification of financial instruments (CFI code)
• ISO/IEC 10967 Information technology – Language independent arithmetic
• ISO/TS 10974:2012 Assessment of the safety of magnetic resonance imaging for patients with an active implantable medical device
• ISO 10985:2009 Caps made of aluminium-plastics combinations for infusion bottles and injection vials – Requirements and test methods
• ISO 10991:2009 Micro process engineering – Vocabulary
• ISO/TR 10992:2011 Intelligent transport systems – Use of nomadic and portable devices to support ITS service and multimedia provision in vehicles
• ISO 10993 Biological evaluation of medical devices
• ISO/IEC 10994:1992 Information technology – Data interchange on 90 mm flexible disk cartridges using modified frequency modulation recording at 31 831 ftprad on 80 tracks on each side – ISO Type 303
• ISO/IEC 10995:2011 Information technology - Digitally recorded media for information interchange and storage - Test method for the estimation of the archival lifetime of optical media

• ISO/IEC 11002:2008 Information technology - Multipath management API
• ISO 11005:2010 Technical product documentation – Use of main documents
• ISO 11011:2013 Compressed air - Energy efficiency - Assessment^[3]
• ISO 11014:2009 Safety data sheet for chemical products - Content and order of sections
• ISO/IEC TR 11017:1998 Information technology - Framework for internationalization
• ISO 11040 Prefilled syringes
  • ISO 11040-1:2015 Part 1: Glass cylinders for dental local anaesthetic cartridges
  • ISO 11040-2:2011 Part 2: Plunger stoppers for dental local anaesthetic cartridges
  • ISO 11040-3:2012 Part 3: Seals for dental local anaesthetic cartridges
  • ISO 11040-4:2015 Part 4: Glass barrels for injectables and sterilized subassembled syringes ready for filling
  • ISO 11040-5:2012 Part 5: Plunger stoppers for injectables
  • ISO 11040-6:2012 Part 6: Plastic barrels for injectables
  • ISO 11040-7:2015 Part 7: Packaging systems for sterilized subassembled syringes ready for filling
  • ISO 11040-8:2016 Part 8: Requirements and test methods for finished prefilled syringes
• ISO 11064 Ergonomic design of control centres
  • ISO 11064-1:2000 Principles for the design of control centres
  • ISO 11064-2:2000 Principles for the arrangement of control suites
  • ISO 11064-3:1999 Control room layout ISO 11064-3:1999/Cor 1:2002
  • ISO 11064-4:2013 Layout and dimensions of workstations
  • ISO 11064-5:2008 Displays and controls
  • ISO 11064-6:2005 Environmental requirements for control centres
  • ISO 11064-7:2006 Principles for the evaluation of control centres
• ISO/TR 11065:1992 Industrial automation glossary
• ISO 11067:2015 Intelligent transport systems – Curve speed warning systems (CSWS) – Performance requirements and test procedures
• ISO 11070:2014 Sterile single-use intravascular introducers, dilators and guidewires
• ISO/IEC 11072:1992 Information technology - Computer graphics - Computer Graphics Reference Model
• ISO/IEEE 11073 Health informatics - Point-of-care medical device communication
• ISO 11074:2015 Soil quality - Vocabulary
• ISO 11086:1996 Gas turbines - Vocabulary
• ISO 11091:1994 Construction drawings – Landscape drawing practice
• ISO 11095:1996 Linear calibration using reference materials
• ISO 11107:2009 Recreational diving services – Requirements for training programmes on enriched air nitrox (EAN) diving
• ISO 11108:1996 Information and documentation - Archival paper - Requirements for permanence and durability
• ISO 11117:2008 Gas cylinders – Valve protection caps and valve guards – Design, construction and tests
• ISO 11120 Gas cylinders - Refillable seamless steel tubes of water capacity between 150 L and 3000 L - Design, construction and testing
• ISO 11121:2017 Recreational diving services – Requirements for introductory programmes to scuba diving
• ISO 11124 Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives
  • ISO 11124-1:1993 Part 1: General introduction and classification
  • ISO 11124-2:1993 Part 2: Chilled-iron grit
  • ISO 11124-3:1993 Part 3: High-carbon cast-steel shot and grit
  • ISO 11124-4:1993 Part 4: Low-carbon cast-steel shot
• ISO 11125 Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives
  • ISO 11125-1:1993 Part 1: Sampling
  • ISO 11125-2:1993 Part 2: Determination of particle size distribution
  • ISO 11125-3:1993 Part 3: Determination of hardness
  • ISO 11125-4:1993 Part 4: Determination of apparent density
  • ISO 11125-5:1993 Part 5: Determination of percentage defective particles and of microstructure
  • ISO 11125-6:1993 Part 6: Determination of foreign matter
  • ISO 11125-7:1993 Part 7: Determination of moisture
• ISO 11126 Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives
  • ISO 11126-1:1993 Part 1: General introduction and classification
  • ISO 11126-3:1993 Part 3: Copper refinery slag
  • ISO 11126-4:1993 Part 4: Coal furnace slag
  • ISO 11126-5:1993 Part 5: Nickel refinery slag
  • ISO 11126-6:1993 Part 6: Iron furnace slag
  • ISO 11126-7:1995 Part 7: Fused aluminium oxide
  • ISO 11126-8:1993 Part 8: Olivine sand
  • ISO 11126-9:1999 Part 9: Staurolite
  • ISO 11126-10:2000 Part 10: Almandite garnet
• ISO 11127 Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives
  • ISO 11127-1:2011 Part 1: Sampling
  • ISO 11127-2:2011 Part 2: Determination of particle size distribution
  • ISO 11127-3:2011 Part 3: Determination of apparent density
  • ISO 11127-4:2011 Part 4: Assessment of hardness by a glass slide test
  • ISO 11127-5:2011 Part 5: Determination of moisture
  • ISO 11127-6:2011 Part 6: Determination of water-soluble contaminants by conductivity measurement
  • ISO 11127-7:2011 Part 7: Determination of water-soluble chlorides
• ISO 11133:2014 Microbiology of food, animal feed and water – Preparation, production, storage and performance testing of culture media
• ISO 11135:2014 Sterilization of health-care products—Ethylene oxide—Requirements for the development, validation and routine control of a sterilization process for medical devices
• ISO 11137 Sterilization of health care products – Radiation
• ISO 11138 Sterilization of health care products - Biological indicators
  • ISO 11138-1:2017 Part 1: General requirements
  • ISO 11138-2:2017 Part 2: Biological indicators for ethylene oxide sterilization processes
  • ISO 11138-3:2017 Part 3: Biological indicators for moist heat sterilization processes
  • ISO 11138-4:2017 Part 4: Biological indicators for dry heat sterilization processes
  • ISO 11138-5:2017 Part 5: Biological indicators for low-temperature steam and formaldehyde sterilization processes
• ISO/TS 11139:2006 Sterilization of health care products - Vocabulary
• ISO 11145:2016 Optics and photonics - Lasers and laser-related equipment - Vocabulary and symbols
• ISO 11146 Lasers and laser-related equipment – Test methods for laser beam widths, divergence angles and beam propagation ratios
  • ISO 11146-1:2005 Part 1: Stigmatic and simple astigmatic beams
  • ISO 11146-2:2005 Part 2: General astigmatic beams
  • ISO/TR 11146-3:2004 Part 3: Intrinsic and geometrical laser beam classification, propagation and details of test methods
• ISO 11151 Lasers and laser-related equipment – Standard optical components
  • ISO 11151-1:2015 Part 1: Components for the UV, visible and near-infrared spectral ranges
  • ISO 11151-2:2015 Part 2: Components for the infrared spectral range
• ISO 11156:2011 Packaging - Accessible design - General requirements
• ISO/IEC 11160 Information technology - Office equipment - Minimum information to be included in specification sheets - Printers
  • ISO/IEC 11160-1:1996 Part 1: Class 1 and Class 2 printers
  • ISO/IEC 11160-2:2013 Part 2: Class 3 and Class 4 printers
• ISO 11170:2003 Hydraulic fluid power – Filter elements – Sequence of tests for verifying performance characteristics
• ISO 11171:2010 Hydraulic fluid power – Calibration of automatic particle counters for liquids
• ISO/IEC 11172 Information technology – Coding of moving pictures and associated audio for digital storage media at up to about 1,5 Mbit/s
• ISO/IEC 11179 Information technology – Metadata registries (MDR)
• ISO 11192:2005 Small craft - Graphical symbols
• ISO 11195:1995 Gas mixers for medical use – Stand-alone gas mixers
• ISO 11197:2016 Medical supply units
• ISO 11200:2014 Acoustics – Noise emitted by machinery and equipment – Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions
• ISO 11201:2010 Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
• ISO 11202:2010 Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
• ISO 11203:1995 Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level
• ISO 11204:2010 Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections
• ISO 11205:2003 Acoustics – Noise emitted by machinery and equipment – Engineering method for the determination of emission sound pressure levels in situ at the work station and at other specified positions using sound intensity
• ISO/TR 11219:2012 Information and documentation - Qualitative conditions and basic statistics for library buildings - Space, function and design
• ISO 11224:2003 Textiles – Web formation and bonding in nonwovens – Vocabulary
• ISO 11238:2012 Health informatics – Identification of medicinal products – Data elements and structures for the unique identification and exchange of regulated information on substances
• ISO 11239:2012 Health informatics – Identification of medicinal products – Data elements and structures for the unique identification and exchange of regulated information on pharmaceutical dose forms, units of presentation, routes of administration and packaging
• ISO 11240:2012 Health informatics – Identification of medicinal products – Data elements and structures for the unique identification and exchange of units of measurement
• ISO/TS 11251:2010 Nanotechnologies – Characterization of volatile components in single-wall carbon nanotube samples using evolved gas analysis/gas chromatograph-mass spectrometry
• ISO 11252:2013 Lasers and laser-related equipment – Laser device – Minimum requirements for documentation
• ISO 11270:2014 Intelligent transport systems – Lane keeping assistance systems (LKAS) – Performance requirements and test procedures
• ISO 11290 Microbiology of the food chain - Horizontal method for the detection and enumeration of Listeria monocytogenes and of Listeria spp.
  • ISO 11290-1:2017 Part 1: Detection method
  • ISO 11290-2:2017 Part 2: Enumeration method
• ISO/TS 11308:2011 Nanotechnologies – Characterization of single-wall carbon nanotubes using thermogravimetric analysis
• ISO 11318:2002 Cardiac defibrillators – Connector assembly DF-1 for implantable defibrillators – Dimensions and test requirements
• ISO/IEC 11319:1993 Information technology – 8 mm wide magnetic tape cartridge for information interchange – Helical scan recording
• ISO/IEC 11321:1992 Information technology – 3,81 mm wide magnetic tape cartridge for information interchange – Helical scan recording – DATA/DAT format
• ISO 11323:2010 Iron ore and direct reduced iron – Vocabulary
• ISO/TR 11328:1994 Measurement of liquid flow in open channels – Equipment for the measurement of discharge under ice conditions
• ISO 11329:2001 Hydrometric determinations – Measurement of suspended sediment transport in tidal channels
• ISO 11357 Plastics – Differential scanning calorimetry (DSC)
  • ISO 11357-1:2009 General principles
  • ISO 11357-2:2013 Determination of glass transition temperature and glass transition step height
  • ISO 11357-3:2011 Determination of temperature and enthalpy of melting and crystallization
  • ISO 11357-4:2005 Determination of specific heat capacity
  • ISO 11357-5:2013 Determination of characteristic reaction-curve temperatures and times, enthalpy of reaction and degree of conversion
  • ISO 11357-6:2008 Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
  • ISO 11357-7:2002 Determination of crystallization kinetics
• ISO/TR 11360:2010 Nanotechnologies – Methodology for the classification and categorization of nanomaterials
• ISO 11375:1998 Building construction machinery and equipment – Terms and definitions
• ISO 11380:1994 Optics and optical instruments – Ophthalmic optics – Formers
• ISO 11381:2016 Ophthalmic optics – Spectacle frames – Screw threads
• ISO 11400:1992 Nickel, ferronickel and nickel alloys - Determination of phosphorus content - Phosphovanadomolybdate molecular absorption spectrometric method
• ISO/IEC 11404:2007 Information technology – General-Purpose Datatypes (GPD)
• ISO/IEC 11411:1995 Information technology - Representation for human communication of state transition of software
• ISO 11418 Containers and accessories for pharmaceutical preparations
  • ISO 11418-1:2016 Part 1: Drop-dispensing glass bottles
  • ISO 11418-2:2016 Part 2: Screw-neck glass bottles for syrups
  • ISO 11418-3:2016 Part 3: Screw-neck glass bottles (veral) for solid and liquid dosage forms
  • ISO 11418-5:2015 Part 5: Dropper assemblies
  • ISO 11418-7:2016 Part 7: Screw-neck vials made of glass tubing for liquid dosage forms
• ISO 11421:1997 Optics and optical instruments - Accuracy of optical transfer function (OTF) measurement
• ISO 11442:2006 Technical product documentation – Document management
• ISO 11446:2004 Road vehicles – Connectors for the electrical connection of towing and towed vehicles – 13-pole connectors for vehicles with 12 V nominal supply voltage
• ISO 11450:1999 Equipment for harvesting and conservation – Round balers – Terminology and commercial specifications
• ISO 11451 Road vehicles – Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy
  • ISO 11451-1:2015 Part 1: General principles and terminology
  • ISO 11451-2:2015 Part 2: Off-vehicle radiation sources
  • ISO 11451-3:2015 Part 3: On-board transmitter simulation
  • ISO 11451-4:2013 Part 4: Bulk current injection (BCI)
• ISO 11452 Road vehicles – Component test methods for electrical disturbances from narrowband radiated electromagnetic energy
  • ISO 11452-1:2015 Part 1: General principles and terminology
  • ISO 11452-2:2004 Part 2: Absorber-lined shielded enclosure
  • ISO 11452-3:2016 Part 3: Transverse electromagnetic (TEM) cell
  • ISO 11452-4:2011 Part 4: Harness excitation methods
  • ISO 11452-5:2002 Part 5: Stripline
  • ISO 11452-7:2003 Part 7: Direct radio frequency (RF) power injection
  • ISO 11452-8:2015 Part 8: Immunity to magnetic fields
  • ISO 11452-9:2012 Part 9: Portable transmitters
  • ISO 11452-10:2009 Part 10: Immunity to conducted disturbances in the extended audio frequency range
  • ISO 11452-11:2010 Part 11: Reverberation chamber
• ISO 11453:1996 Statistical interpretation of data - Tests and confidence intervals relating to proportions
• ISO/IEC 11458:1993 Information technology - Microprocessor systems - VICbus - Inter-crate cable bus
• ISO 11462 Guidelines for implementation of statistical process control (SPC)
  • ISO 11462-1:2001 Part 1: Elements of SPC
  • ISO 11462-2:2010 Part 2: Catalogue of tools and techniques
• ISO 11469:2000 Plastics – Generic identification and marking of plastics products
• ISO 11484:2009 Steel products – Employer's qualification system for non-destructive testing (NDT) personnel
• ISO 11485 Glass in building – Curved glass
  • ISO 11485-1:2011 Part 1: Terminology and definitions
• ISO/TR 11487:2008 Health informatics – Clinical stakeholder participation in the work of ISO TC 215
• ISO 11491:2017 Implants for surgery – Determination of impact resistance of ceramic femoral heads for hip joint prostheses
• ISO 11499:2014 Dentistry – Single-use cartridges for local anaesthetics
• ISO/IEC 11518 Information technology - High-Performance Parallel Interface
  • ISO/IEC 11518-1:1995 Part 1: Mechanical, electrical and signalling protocol specification (HIPPI-PH)
  • ISO/IEC 11518-2:2000 Part 2: Framing Protocol (HIPPI-FP)
  • ISO/IEC 11518-3:1996 Part 3: Encapsulation of ISO/IEC 8802-2 (IEEE Std 802.2) Logical Link Control Protocol Data Units (HIPPI-LE)
  • ISO/IEC 11518-6:2000 Part 6: Physical Switch Control (HIPPI-SC)
  • ISO/IEC 11518-9:1999 Part 9: Serial specification (HIPPI-Serial)
  • ISO/IEC 11518-10:2001 Part 10: 6400 Mbit/s Physical Layer (HIPPI-6400-PH)
• ISO 11532:2012 Aircraft ground equipment - Graphical symbols
• ISO/IEC 11544:1993 Information technology - Coded representation of picture and audio information - Progressive bi-level image compression
• ISO 11546 Acoustics – Determination of sound insulation performances of enclosures
  • ISO 11546-1:1995 Part 1: Measurements under laboratory conditions (for declaration purposes)
  • ISO 11546-2:1995 Part 2: Measurements in situ (for acceptance and verification purposes)
• ISO/TR 11548 Communication aids for blind persons - Identifiers, names and assignation to coded character sets for 8-dot Braille characters
  • ISO/TR 11548-1:2001 Part 1: General guidelines for Braille identifiers and shift marks
  • ISO/TR 11548-2:2001 Part 2: Latin alphabet based character sets
• ISO 11551:2003 Optics and optical instruments – Lasers and laser-related equipment – Test method for absorptance of optical laser components
• ISO 11553 Safety of machinery – Laser processing machines
  • ISO 11553-1:2005 Part 1: General safety requirements
  • ISO 11553-2:2007 Part 2: Safety requirements for hand-held laser processing devices
  • ISO 11553-3:2013 Part 3: Noise reduction and noise measurement methods for laser processing machines and hand-held processing devices and associated auxiliary equipment (accuracy grade 2)
• ISO 11554:2017 Optics and photonics – Lasers and laser-related equipment – Test methods for laser beam power, energy and temporal characteristics
• ISO/IEC 11557:1992 Information technology – 3,81 mm wide magnetic tape cartridge for information interchange – Helical scan recording – DDS-DC format using 60 m and 90 m length tapes
• ISO/IEC 11558:1992 Information technology – Data compression for information interchange – Adaptive coding with embedded dictionary – DCLZ Algorithm
• ISO/IEC 11559:1993 Information technology – Data interchange on 12,7 mm wide 18-track magnetic tape cartridges – Extended format
• ISO/IEC 11560:1992 Information technology - Information interchange on 130 mm optical disk cartridges using the magneto-optical effect, for write once, read multiple functionality
• ISO 11568 Financial services – Key management (retail)^{[Note 4]}
  • ISO 11568-1:2005 Part 1: Principles
  • ISO 11568-2:2012 Part 2: Symmetric ciphers, their key management and life cycle
  • ISO 11568-4:2007 Part 4: Asymmetric cryptosystems – Key management and life cycle
• ISO/IEC 11569:1993 Information technology – Telecommunications and information exchange between systems – 26-pole interface connector mateability dimensions and contact number assignments
• ISO/IEC 11570:1992 Information technology – Telecommunications and information exchange between systems – Open Systems Interconnection – Transport protocol identification mechanism
• ISO/IEC 11571:1998 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Networks – Addressing
• ISO/IEC 11572:2000 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Circuit mode bearer services – Inter-exchange signalling procedures and protocol
• ISO/IEC 11573:1994 Information technology – Telecommunications and information exchange between systems – Synchronization methods and technical requirements for Private Integrated Services Networks
• ISO/IEC 11574:2000 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Circuit-mode 64 kbit/s bearer services – Service description, functional capabilities and information flows
• ISO/IEC 11575:1995 Information technology – Telecommunications and information exchange between systems – Protocol mappings for the OSI Data Link service
• ISO/IEC 11576:1994 Information technology – Procedure for the registration of algorithms for the lossless compression of data
• ISO/IEC 11577:1995 Information technology – Open Systems Interconnection – Network layer security protocol
• ISO/IEC 11578:1996 Information technology – Open Systems Interconnection – Remote procedure call (RPC)
• ISO/IEC 11579 Information technology – Telecommunications and information exchange between systems – Private integrated services network
  • ISO/IEC 11579-1:1994 Part 1: Reference configuration for PISN Exchanges (PINX)
  • ISO/IEC 11579-2:1999 Part 2: Reference configuration for HS-PISN Exchanges (HS-PINX)
  • ISO/IEC 11579-3:1999 Part 3: Reference configuration for PINX extension lines
• ISO/IEC TR 11580:2007 Information technology – Framework for describing user interface objects, actions and attributes
• ISO/IEC 11581 Information technology – User interface icons^{[Note 4]}
  • ISO/IEC 11581-1:2000 Part 1: Icons – General
  • ISO/IEC TR 11581-1:2011 Part 1: Introduction to and overview of icon standards
  • ISO/IEC 11581-2:2000 Part 2: Object icons
  • ISO/IEC 11581-3:2000 Part 3: Pointer icons
  • ISO/IEC 11581-5:2004 Part 5: Tool icons
  • ISO/IEC 11581-6:1999 Part 6: Action icons
  • ISO/IEC 11581-10:2010 Part 10: Framework and general guidance
  • ISO/IEC 11581-40:2011 Part 40: Management of icon registration
  • ISO/IEC TS 11581-41:2014 Part 41: Data structure to be used by the ISO/IEC JTC 1/SC 35 icon database
• ISO/IEC 11582:2002 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Generic functional protocol for the support of supplementary services – Inter-exchange signalling procedures and protocol
• ISO/TR 11583:2012 Measurement of wet gas flow by means of pressure differential devices inserted in circular cross-section conduits
• ISO/IEC 11584:1996 Information technology – Telecommunications and information exchange between systems – Private Integrated Services Network – Circuit-mode multi-rate bearer services – Service description, functional capabilities and information flows
• ISO/IEC 11586 Information technology - Open Systems Interconnection - Generic upper layers security
  • ISO/IEC 11586-1:1996 Overview, models and notation
  • ISO/IEC 11586-2:1996 Security Exchange Service Element (SESE) service definition
  • ISO/IEC 11586-3:1996 Security Exchange Service Element (SESE) protocol specification
  • ISO/IEC 11586-4:1996 Protecting transfer syntax specification
  • ISO/IEC 11586-5:1997 Security Exchange Service Element (SESE) Protocol Implementation Conformance Statement (PICS) proforma
  • ISO/IEC 11586-6:1997 Protecting transfer syntax Protocol Implementation Conformance Statement (PICS) proforma
• ISO/IEC 11587:1996 Information technology – Open Systems Interconnection – Application Context for Systems Management with Transaction Processing
• ISO 11593:1996 Manipulating industrial robots - Automatic end effector exchange systems - Vocabulary and presentation of characteristics
• ISO 11607:2006 Packaging for Terminally Sterilized Medical Devices
• ISO 11608 Needle-based injection systems for medical use – Requirements and test methods^{[Note 4]}
  • ISO 11608-1:2014 Part 1: Needle-based injection systems
  • ISO 11608-2:2012 Part 2: Needles
  • ISO 11608-3:2012 Part 3: Finished containers
  • ISO 11608-4:2006 Part 4: Requirements and test methods for electronic and electromechanical pen-injectors
  • ISO 11608-5:2012 Part 5: Automated functions
  • ISO 11608-7:2016 Part 7: Accessibility for persons with visual impairment
• ISO 11609:2017 Dentistry - Dentifrices - Requirements, test methods and marking
• ISO/TR 11610:2004 Protective clothing - Vocabulary
• ISO 11612 Protective clothing - Protection against brief contact with heat and flame. The heat can be convective, radiant, molten material, or a combination thereof.
• ISO 11615:2012 Health informatics – Identification of medicinal products – Data elements and structures for the unique identification and exchange of regulated medicinal product information
• ISO 11616:2012 Health informatics – Identification of medicinal products – Data elements and structures for the unique identification and exchange of regulated pharmaceutical product information
• ISO 11620:2014 Information and documentation - Library performance indicators
• ISO 11631:1998 Measurement of fluid flow – Methods of specifying flowmeter performance
• ISO/TR 11633 Health informatics – Information security management for remote maintenance of medical devices and medical information systems
  • ISO/TR 11633-1:2009 Part 1: Requirements and risk analysis
  • ISO/TR 11633-2:2009 Part 2: Implementation of an information security management system (ISMS)
• ISO/TR 11636:2009 Health Informatics – Dynamic on-demand virtual private network for health information infrastructure
• ISO 11648 Statistical aspects of sampling from bulk materials
  • ISO 11648-1:2003 Part 1: General principles
  • ISO 11648-2:2001 Part 2: Sampling of particulate materials
• ISO 11649:2009 Financial services – Core banking – Structured creditor reference to remittance information
• ISO/TR 11651:2015 Estimation of sediment deposition in reservoirs using one dimensional simulation models
• ISO 11655:1995 Measurement of liquid flow in open channels – Method of specifying performance of hydrometric equipment
• ISO 11657:2014 Hydrometry – Suspended sediment in streams and canals – Determination of concentration by surrogate techniques
• ISO 11658:2012 Cardiovascular implants and extracorporeal systems – Blood/tissue contact surface modifications for extracorporeal perfusion systems
• ISO 11663:2014 Quality of dialysis fluid for haemodialysis and related therapies
• ISO 11664 Colorimetry
  • ISO 11664-1:2007 Part 1: CIE standard colorimetric observers
  • ISO 11664-2:2007 Part 2: CIE standard illuminants
  • ISO 11664-3:2012 Part 3: CIE tristimulus values
  • ISO 11664-4:2008 Part 4: CIE 1976 L*a*b* Colour space
  • ISO/CIE 11664-5:2016 Part 5: CIE 1976 L*u*v* colour space and u', v' uniform chromaticity scale diagram
  • ISO/CIE 11664-6:2014 Part 6: CIEDE2000 Colour-difference formula
• ISO 11665 Measurement of radioactivity in the environment - Air: radon-222
  • ISO 11665-1:2012 Part 1: Origins of radon and its short-lived decay products and associated measurement methods
  • ISO 11665-2:2012 Part 2: Integrated measurement method for determining average potential alpha energy concentration of its short-lived decay products
  • ISO 11665-3:2012 Part 3: Spot measurement method of the potential alpha energy concentration of its short-lived decay products
  • ISO 11665-4:2012 Part 4: Integrated measurement method for determining average activity concentration using passive sampling and delayed analysis
  • ISO 11665-5:2012 Part 5: Continuous measurement method of the activity concentration
  • ISO 11665-6:2012 Part 6: Spot measurement method of the activity concentration
  • ISO 11665-7:2012 Part 7: Accumulation method for estimating surface exhalation rate
  • ISO 11665-8:2012 Part 8: Methodologies for initial and additional investigations in buildings
  • ISO 11665-9:2016 Part 9: Test methods for exhalation rate of building materials
  • ISO 11665-11:2016 Part 11: Test method for soil gas with sampling at depth
• ISO/TS 11669:2012 Translation projects - General guidance
• ISO 11670:2003 Lasers and laser-related equipment – Test methods for laser beam parameters – Beam positional stability
• ISO/TS 11672:2016 Connectors for fluid power and general use - Designation and nomenclature
• ISO 11675:2005 Textile machinery and accessories – Flatbed knitting machines – Vocabulary
• ISO 11676:2014 Textile machinery and accessories – Pattern disks and pattern chains for warp knitting machines – Vocabulary and symbols
• ISO 11683:1997 Packaging - Tactile warnings of danger - Requirements
• ISO 11684:1995 Tractors, machinery for agriculture and forestry, powered lawn and garden equipment - Safety signs and hazard pictorials - General principles
• ISO/TR 11688 Acoustics – Recommended practice for the design of low-noise machinery and equipment
  • ISO/TR 11688-1:1995 Part 1: Planning
  • ISO/TR 11688-2:1998 Part 2: Introduction to the physics of low-noise design
• ISO 11689:1996 Acoustics – Procedure for the comparison of noise-emission data for machinery and equipment
• ISO/IEC 11693 Identification cards – Optical memory cards
  • ISO/IEC 11693-1:2012 Part 1: General characteristics
  • ISO/IEC 11693-2:2009 Part 2: Co-existence of optical memory with other machine readable technologies
  • ISO/IEC 11693-3:2015 Part 3: Authentication techniques
• ISO/IEC 11694 Identification cards – Optical memory cards – Linear recording method
  • ISO/IEC 11694-1:2012 Part 1: Physical characteristics
  • ISO/IEC 11694-2:2012 Part 2: Dimensions and location of the accessible optical area
  • ISO/IEC 11694-3:2015 Part 3: Optical properties and characteristics
  • ISO/IEC 11694-4:2008 Part 4: Logical data structures
  • ISO/IEC 11694-5:2014 Part 5: Data format for information interchange for applications using ISO/IEC 11694-4
  • ISO/IEC 11694-6:2014 Part 6: Use of biometrics on an optical memory card
• ISO/IEC 11695 Identification cards – Optical memory cards – Holographic recording method
  • ISO/IEC 11695-1:2015 Part 1: Physical characteristics
  • ISO/IEC 11695-2:2015 Part 2: Dimensions and location of accessible optical area
  • ISO/IEC 11695-3:2017 Part 3: Optical properties and characteristics
• ISO 11704:2010 Water quality - Measurement of gross alpha and beta activity concentration in non-saline water - Liquid scintillation counting method
• ISO 11712:2009 Anaesthetic and respiratory equipment – Supralaryngeal airways and connectors
• ISO 11731:2017 Water quality - Enumeration of Legionella
• ISO 11737 Sterilization of medical devices – Microbiological methods
  • ISO 11737-1:2006 Part 1: Determination of a population of microorganisms on products
  • ISO 11737-2:2009 Part 2: Tests of sterility performed in the definition, validation and maintenance of a sterilization process
• ISO/IEC 11756:1999 Information technology - Programming languages - M
• ISO/TR 11766:2010 Intelligent transport systems – Communications access for land mobiles (CALM) – Security considerations for lawful interception
• ISO/TR 11769:2010 Intelligent transport systems – Communications access for land mobiles (CALM) – Data retention for law enforcement
• ISO/IEC 11770 Information technology - Security techniques - Key management
  • ISO/IEC 11770-1:2010 Part 1: Framework
  • ISO/IEC 11770-2:2008 Part 2: Mechanisms using symmetric techniques
  • ISO/IEC 11770-3:2015 Part 3: Mechanisms using asymmetric techniques
  • ISO/IEC 11770-4:2006 Part 4: Mechanisms based on weak secrets
  • ISO/IEC 11770-5:2011 Part 5: Group key management
  • ISO/IEC 11770-6:2016 Part 6: Key derivation
• ISO/TS 11774:2011 Non-destructive testing – Performance-based qualification
• ISO 11783 Tractors and machinery for agriculture and forestry – Serial control and communications data network
• ISO 11798:1999 Information and documentation - Permanence and durability of writing, printing and copying on paper - Requirements and test methods
• ISO 11799:2015 Information and documentation - Document storage requirements for archive and library materials
• ISO 11800:1998 Information and documentation – Requirements for binding materials and methods used in the manufacture of books
• ISO/IEC 11801:2002 Information technology – Generic cabling for customer premises^{[Note 4]}
  • ISO/IEC TR 11801-9901:2014 Part 9901: Guidance for balanced cabling in support of at least 40 Gbit/s data transmission
  • ISO/IEC TR 11801-9902:2017 Part 9902: Specifications for End-to-end link configurations
  • ISO/IEC TR 11801-9903:2015 Part 9903: Matrix modelling of channels and links
  • ISO/IEC TR 11801-9904:2017 Part 9904: Guidelines for the use of installed cabling to support 2,5GBASE -T and 5GBASE -T applications
• ISO/IEC TR 11802 Information technology – Telecommunications and information exchange between systems – Local and metropolitan area networks – Technical reports and guidelines
  • ISO/IEC TR 11802-5:1997 Part 5: Media Access Control (MAC) Bridging of Ethernet V2.0 in Local Area Networks
• ISO 11807 Integrated optics - Vocabulary
  • ISO 11807-1:2001 Part 1: Basic terms and symbols
  • ISO 11807-2:2001 Part 2: Terms used in classification
• ISO 11810:2015 Lasers and laser-related equipment – Test method and classification for the laser resistance of surgical drapes and/or patient protective covers – Primary ignition, penetration, flame spread and secondary ignition
• ISO/TR 11811:2012 Nanotechnologies – Guidance on methods for nano- and microtribology measurements
• ISO 11819 Acoustics – Measurement of the influence of road surfaces on traffic noise^{[Note 4]}
  • ISO 11819-1:1997 Part 1: Statistical Pass-By method
  • ISO 11819-2:2017 Part 2: The close-proximity method
  • ISO/TS 11819-3:2017 Part 3: Reference tyres
  • ISO/PAS 11819-4:2013 Part 4: SPB method using backing board
• ISO 11821:1997 Acoustics – Measurement of the in situ sound attenuation of a removable screen
• ISO 11822:1996 Information and documentation - Extension of the Arabic alphabet coded character set for bibliographic information interchange
• ISO 11838:1997 Motorcycle and motorcycle-rider kinematics – Vocabulary
• ISO 11841 Road vehicles and internal combustion engines – Filter vocabulary
  • ISO 11841-1:2000 Part 1: Definitions of filters and filter components
  • ISO 11841-2:2000 Part 2: Definitions of characteristics of filters and their components
• ISO 11843 Capability of detection
  • ISO 11843-1:1997 Part 1: Terms and definitions
  • ISO 11843-2:2000 Part 2: Methodology in the linear calibration case
  • ISO 11843-3:2003 Part 3: Methodology for determination of the critical value for the response variable when no calibration data are used
  • ISO 11843-4:2003 Part 4: Methodology for comparing the minimum detectable value with a given value
  • ISO 11843-5:2008 Part 5: Methodology in the linear and non-linear calibration cases
  • ISO 11843-6:2013 Part 6: Methodology for the determination of the critical value and the minimum detectable value in Poisson distributed measurements by normal approximations
  • ISO 11843-7:2012 Part 7: Methodology based on stochastic properties of instrumental noise
• ISO 11866 Milk and milk products – Enumeration of presumptive Escherichia coli
  • ISO 11866-1:2005 Part 1: Most probable number technique using 4-methylumbelliferyl-beta-D-glucuronide (MUG)
  • ISO 11866-2:2005 Part 2: Colony-count technique at 44 degrees C using membranes
• ISO 11886:2002 Building construction machinery and equipment – Pile driving and extracting equipment – Terminology and commercial specifications
• ISO/TS 11888:2017 Nanotechnologies – Characterization of multiwall carbon nanotubes – Mesoscopic shape factors
• ISO/IEC 11889 Information technology - Trusted platform module library
  • ISO/IEC 11889-1:2015 Part 1: Architecture
  • ISO/IEC 11889-2:2015 Part 2: Structures
  • ISO/IEC 11889-3:2015 Part 3: Commands
  • ISO/IEC 11889-4:2015 Part 4: Supporting Routines
• ISO 11898 Road vehicles – Controller area network (CAN)
• ISO 11904 Acoustics – Determination of sound immission from sound sources placed close to the ear
  • ISO 11904-1:2002 Part 1: Technique using a microphone in a real ear (MIRE technique)
  • ISO 11904-2:2004 Part 2: Technique using a manikin
• ISO 11929:2010 Determination of the characteristic limits (decision threshold, detection limit and limits of the confidence interval) for measurements of ionizing radiation - Fundamentals and application
• ISO 11930:2012 Cosmetics – Microbiology – Evaluation of the antimicrobial protection of a cosmetic product
• ISO/TS 11931:2012 Nanotechnologies – Nanoscale calcium carbonate in powder form – Characteristics and measurement
• ISO/TS 11937:2012 Nanotechnologies – Nanoscale titanium dioxide in powder form – Characteristics and measurement
• ISO 11940:1998 Information and documentation - Transliteration of Thai
  • ISO 11940-2:2007 Information and documentation - Transliteration of Thai characters into Latin characters - Part 2: Simplified transcription of Thai language
• ISO/TR 11941:1996 Information and documentation - Transliteration of Korean script into Latin characters [Withdrawn, no replacement]
• ISO 11957:1996 Acoustics – Determination of sound insulation performance of cabins – Laboratory and in situ measurements
• ISO/IEC 11976:2008 Information technology - Data interchange on 130 mm rewritable and write-once-read-many ultra density optical (UDO) disk cartridges - Capacity: 60 Gbytes per cartridge - Second generation
• ISO 11978:2017 Ophthalmic optics – Contact lenses and contact lens care products – Labelling
• ISO 11979 Ophthalmic implants - Intraocular lenses
  • ISO 11979-1:2012 Part 1: Vocabulary
  • ISO 11979-2:2014 Part 2: Optical properties and test methods
  • ISO 11979-3:2012 Part 3: Mechanical properties and test methods
  • ISO 11979-4:2008 Part 4: Labelling and information
  • ISO 11979-5:2006 Part 5: Biocompatibility
  • ISO 11979-6:2014 Part 6: Shelf-life and transport stability testing
  • ISO 11979-7:2014 Part 7: Clinical investigations
  • ISO 11979-8:2017 Part 8: Fundamental requirements
  • ISO 11979-9:2006 Part 9: Multifocal intraocular lenses
  • ISO 11979-10:2006 Part 10: Phakic intraocular lenses
• ISO 11980:2012 Ophthalmic optics – Contact lenses and contact lens care products – Guidance for clinical investigations
• ISO 11981:2009 Ophthalmic optics – Contact lenses and contact lens care products – Determination of physical compatibility of contact lens care products with contact lenses
• ISO 11986:2010 Ophthalmic optics – Contact lenses and contact lens care products – Determination of preservative uptake and release
• ISO 11987:2012 Ophthalmic optics – Contact lenses – Determination of shelf-life
• ISO/IEC 11989:2010 Information technology - iSCSI Management API
• ISO 11990 Lasers and laser-related equipment – Determination of laser resistance of tracheal tubes
  • ISO 11990-1:2011 Part 1: Tracheal tube shaft
  • ISO 11990-2:2010 Part 2: Tracheal tube cuffs
• ISO/TR 11991:1995 Guidance on airway management during laser surgery of upper airway
• ISO 11994:1997 Cranes – Availability – Vocabulary

• International Organization for Standardization
• ISO Certification Provider
• ISO Consultant