BMW M70

BMW M70 engine
Overview
Production	1987–1994
Layout
Configuration	60° V12
Displacement	5.0 L (4,988 cc)
Cylinder bore	84 mm (3.31 in)
Piston stroke	75 mm (2.95 in)
Cylinder block material	Aluminium
Cylinder head material	Aluminium
Valvetrain	SOHC
Combustion
Fuel type	Petrol
Output
Power output	220 kW (295 hp)
Torque output	450 N⋅m (332 lb⋅ft)
Chronology
Predecessor	None
Successor	BMW M73

The BMW M70 is a naturally-aspirated, SOHC, V12 petrol engine, which was BMW's first production V12^[1] and was produced from 1987 to 1996. It was also the first German 12-cylinder post-war automobile engine, predating Mercedes-Benz's M120 by four years and VAG's W12 by fourteen.

The BMW S70/2 engine, largely unrelated to the M70 and S70B56 engines, is a naturally-aspirated, DOHC, V12 petrol engine, which powered the 1993 to 1998 McLaren F1.

The M70's design is similar to that of two 2.5 L M20 straight-six engines joined at a 60-degree angle,^[2] due to the following features: single overhead camshaft valvetrain, bore spacing of 91 mm (3.6 in), bore of 84 mm (3.31 in), stroke of 75 mm (2.95 in), and a compression ratio of 8.8:1.^[3]

The M70 has the following differences with the M20 engine:

• Aluminium alloy engine block (AluSil) instead of cast-iron (both engines have an aluminium cylinder head), to reduce weight.^[4]
• Airflow measurement using Mass air flow sensors (MAFs)^[5] instead of Air flow meters (AFMs) to improve fuel economy.
• Electronic Throttle Control instead of a mechanical throttle cable.
• A timing chain was used instead of a timing belt,^[6] to reduce servicing requirements.
• Hydraulic valve lifters instead of mechanically adjusted tappets, to reduce servicing requirements.

The M70 has two Motronic 1.3^[7] ECUs (one for each cylinder bank). To provide redundancy, the M70 also has two fuel pumps, fuel rails, distributors, mass air flow sensors, crankshaft position sensors, coolant temperature sensors and throttle bodies.^[8]

Some M70 engines (such as fitted to the E32 750iL Highline) are fitted with two alternators. The second alternator is smaller and is used to charge an auxiliary battery and power equipment in the rear passenger compartment, such as a telephone, fax machine, wine cooler, independent climate control and power sun shields.^[9]

Applications:

• 1987–1994 E32 750i/750iL – this was mated primarily to an automatic ZF 4HP24 transmission
• 1989–1994 E31 850i/850Ci – this was mated to either the automatic ZF 4HP24 transmission or the optional Getrag 560G
• 1988 Alpina B12
• 1991 BMW Nazca M12
• 1992 BMW Nazca C2

BMW S70 engine
Engine bay of a McLaren F1
Overview
Production	1992–2000
Layout
Configuration	60° V12
Displacement	5.6 L (5,576 cc) 6.1 L (6,064 cc) 6.0 L (5,990 cc)
Cylinder bore	86 mm (3.39 in)
Piston stroke	80 mm (3.15 in) 87 mm (3.43 in) 85.9 mm (3.38 in)
Cylinder block material	Aluminium
Cylinder head material	Aluminium
Valvetrain	DOHC
Compression ratio	11:1
Combustion
Fuel type	Petrol
Cooling system	Water-cooled
Output
Power output	280–671 kW (375–900 hp)*(*900 PS produced only McLaren F1 GTR Long Tail specifically in full race trim upon qualification without racing restrictors)[13][14][15][16]
Torque output	550–900 N⋅m (406–664 lb⋅ft)
Dimensions
Dry weight	265 kg (584 lb)
Chronology
Predecessor	None
Successor	None

The first engine to use the S70 name is a 5,576 cc (340.3 cu in) variant of the M70 engine fitted only to the E31 850CSi.^[17] With 1,510 units produced, this is the lowest production BMW engine to date.^[18]

Three prototype dual overhead camshaft S70 engines were constructed, prior to the decision to not produce an E31 M8 model.^[19]

Applications:

• 1992–1996 E31 850CSi
• 1993 BMW Nazca C2 Spider
• 2011 Simbol Design Lavazza GTX-R (twin-turbo version)

The S70/2, while sharing the same 12 cylinder layout, bore spacing and design principle as the S70B56, is essentially a new design with the heads based on the European market S50B30,^[20] and thus featuring 4 valves per cylinder and variable valve timing (called VANOS by BMW) and individual throttle bodies. A dry sump oiling system is used.^[21] The weight of the S70/2, plus ancillaries and full exhaust, is 265 kg (584 lb).^[22]

Applications:

• 1993–1998 McLaren F1

The S70/3 is a racing engine based on the S70/2.

Applications

• 1998–1999 BMW V12 LM racing car
• 1999–2000 BMW V12 LMR racing car
• 2000 BMW X5 LM concept car^[23][24][25]

• BMW Goldfish V16

Wikimedia Commons has media related to BMW M70 engine.